1193人阅读
The first thing you'll need is two computers. You need not have identical hardware in both machines (or amount of memory, etc.), but if you did, it would make your life that much easier when a component fails. Now you have to decide on some of your implementation. Your && is established via a &heartbeat& between the two computers () generated by . However, this heartbeat needs one or more media paths (serial via a null modem cable, Ethernet via a crossover cable, etc.) between the nodes. At this point, you're actually ready to begin hardware-wise. Of course, since you're looking into HA, you'll mostly likely want to avoid having only one point of failure. In this case, that would be your null modem cable/serial port or network interface card (NIC)/crossover cable. So, you need to decide whether you wish to add a second serial/null modem connection or a second network interface card (NIC)/crossover connnection to each node. See
for instructions on how to build a Cat-5 crossover cable. My heartbeat path setup uses one serial port and one extra NIC because I only had one null modem cable, had an extra of NIC on hand and thought it was good to have two medium types for the heartbeats. Once your hardware is in order, you must install your OS and configure your networking (I used Red Hat). Assuming you have 2 NICs, one should be configured for your &normal& network and the other as a private network between your clustered nodes (via the crossover cable). For an example, we will assume that our cluster will have the following addresses: Node 1 (linuxha1)192.168.85.1 (normal 192x net)10.0.0.1 (private 10x net for heartbeat)Node 2 (linuxha2)192.168.85.2 (192x)10.0.0.2 (10x)Note: None of these addresses should be your &cluster address& - the address handled by
between nodes! Most *nix distributions this easy during installation, however, if you are having any problems, refer to either the Ethernet HOWTO, or the documentation for your distribution. To check your configuration, type: ifconfig
This will show your network interfaces and their configuration. You can obtain your network routing information from &netstat&-nr&. If it looks good, make sure you can ping between both nodes on all interfaces. Next, if you're using one, you'll need to test your serial connection. On one node, which will be the receiver, type: cat &/dev/ttyS0
On the other node, type: echo hello &/dev/ttyS0You should see the text on the receiver node. If it works, change their roles and try again. If it doesn't, it may be as simple as having the wrong device file. Volker's HA Hardware Guide and the Serial HOWTO are two good resources for troubleshooting your serial connection. You can now install the
package. If you're reading this, you probably already have it, but in any case it's available at:
There are binary s at the website, or you can build Heartbeat from source. Grab the tarball (or install the source RPM). Untar it into your favorite source directory. From the top of the source tree, type &./ConfigureMe&configure&, followed by &make& and &make&install&. If you have problems installing the RPMs found at the website and want a way to make your own, there may be help in the . There are three files you will need to configure before starting up . The first is . This will be placed in the /etc/ha.d directory that is created after installation. It tells Heartbeat what types of media paths to use and how to configure them. The
in the source directory contains all the various options you can use, I'll go through it line by line... serial /dev/ttyS0
Use a serial heartbeat - if you don't use a serial heartbeat, you must use another medium, such as a
(Ethernet) heartbeat. Replace /dev/ttyS0 with the appropriate device file for your required serial heartbeat. watchdog /dev/watchdog
Optional. The watchdog function provides a way to have a system that is still minimally functioning, but not providing a heartbeat, reboot itself after a minute of being sick. This could help to avoid a scenario where the machine recovers its heartbeat after being pronounced dead. If that happened and a disk mount failed over, you could have two nodes mounting a disk simultaneously. If you wish to use this feature, then in addition to this line, you will need to load the && kernel module and create the actual device file. To do this, first type &insmod&softdog& to load the module. Then, type &grep&misc&/proc/devices& and note the number it reports (should be 10). Next, type &cat&/proc/misc&|&grep&watchdog& and note that number (should be 130). Now you can create the device file with that info typing, &mknod&/dev/watchdog&c&10&130&. bcast eth1
Specifies to use a broadcast heartbeat over the eth1 interface (replace with eth0, eth2, or whatever you use). keepalive 2
Sets the time between heartbeats to 2 seconds. warntime 10
Time in seconds before issuing a &late heartbeat& warning in the logs. deadtime 30
Node is pronounced dead after 30 seconds. initdead 120
With some configurations, the network takes some time to start working after a reboot. This is a separate &deadtime& to handle that case. It should be at least twice the normal . baud 19200
Speed at which to run the serial line (bps). udpport 694
Use port number 694 for
communication. This is the default, and the official IANA registered port number. auto_failback on
Required. For those familiar with Tru64 Unix, Heartbeat acts as if in &favored member& mode. The master listed in the
file holds all the s until a failover, at which time the slave takes over. When
is set to on once the master comes back online, it will take everything back from the slave. When set to off this option will prevent the master node from re-acquiring cluster resources after a failover. This option is similar to to the obsolete nice_failback option. If you want to upgrade from a cluster which had nice_failback set off, to this or later versions, special considerations apply in order to want to avoid requiring a flash cut. Please see the
for details on how to deal with this situation. node linuxha1.linux-ha.org
Mandatory. Hostname of machine in cluster as described by uname&-n. node linuxha2.linux-ha.org
Mandatory. Hostname of machine in cluster as described by uname&-n. respawn userid cmd
Optional: Lists a command to be spawned and monitored. E.g.: To spawn ccm daemons the following line has to be added: respawn hacluster /usr/lib/heartbeat/ccm
Informs Heartbeat to spawn the command with the credentials of that of userid (hacluster, in this example) and monitors the health of the process, respawning it if dead. For , the line would be: respawn hacluster /usr/lib/heartbeat/ipfail
NOTE: If the process dies with exit code 100, the process is not respawned. ping ping1.linux-ha.org ping2.linux-ha.org ....
Optional: Specify . These nodes are not considered as cluster s. They are used to check network connectivity for modules like . ping_group name ping1.linux-ha.org ping2.linux-ha.org ....
Optional: Specify a group of ping nodes. These are similar to , but if any node in a group is available then the group is considered available. The group name can be any string and is used to uniquely identify the group. Each group must appear on a separate line. Like ping nodes the group is not considered to be a cluster node. They appear to be the same as ping nodes and are used to check network connectivity for modules like . Once you've got your
set up, you need to configure . This file specifies the services for the cluster and who the default owner is. Note: This file must be the same on both nodes or . For our example, we'll assume the high availability services are Apache and Samba. The IP for the cluster is mandatory, and don't configure the cluster IP outside of the
file!. The
will need one line: linuxha1.linux-ha.org 192.168.85.3 httpd smb
So, this line dictates that on startup, have linuxha1 serve the IP 192.168.85.3 and start Apache and Samba as well. On shutdown,
will first stop smb, then Apache, then give up the IP. This assumes that the command &uname&-n& spits out &linuxha1.linux-ha.org& - yours may well produce &linuxha1& and if it does, use that instead! Note: httpd and smb are the name of startup scripts for Apache and Samba, respectively.
will look for startup scripts of the same name in the following paths: /etc/ha.d/resource.d
/etc/init.d
These scripts must start services via &scriptname&start& and stop them via &scriptname&stop&. So you can use any services as long as they conform to the above standard. Should you need to pass arguments to a custom script, the format would be: scriptname::argument
So, if we added a service &maid& which needed the argument &vacuum&, our
line would modify to the following: linuxha1 192.168.85.3 httpd smb maid::vacuum
This brings us to some added flexibility with the service IP address. We are actually using a shorthand notation above. The actual line could have read (we've canned the maid): linuxha1 IPaddr::192.168.85.3 httpd smb
Where IPaddr is the name of our service script, taking the argument 192.168.85.3. Sure enough, if you look in the directory /etc/ha.d/resource.d, you will find a script called IPaddr. This script will also allow you to manipulate the netmask, broadcast address and base interface of this IP service. To specify a subnet with 32 addresses, you could define the service as (leaving off the IPaddr because we can!): linuxha1 192.168.85.3/27 httpd smb
This sets the IP service address to 192.168.85.3, the netmask to 255.255.255.224 and the broadcast address would default to 192.168.85.31 (which is the highest address on the subnet). The last parameter you can set is the broadcast address. To override the default and set it to 192.168.85.16, your entry would read: linuxha1 192.168.85.3/27/192.168.85.16 httpd smb
You may be wondering whether any of the above is necessary for you. It depends. If you've properly established a net route (independent of ) for the service's IP address, with the correct netmask and broadcast address, then no, it's not necessary for you. However, this case won't fit everybody and that's why the option's there! In addition, you may have more than one possible interface that could be used for the service IP. Read on to see how Heartbeat treats this... Once you straighten out your
file, copy
to /etc/ha.d and you're ready to start! The
plugin attempts to provide detection of network failures, and then intelligently react, directing the cluster to
s as necessary. In order to accomplish this goal, it uses
or ping groups which work as &dumb& third parties in the cluster. Provided both HA nodes can communicate with each other,
can reliably detect when one of their network links has become unusable, and compensate. To configure , the following steps must be performed. Select good
candidates. It is essential that good strategic ping nodes be selected. The better your choices, the stronger your HA cluster becomes. Choosing solid network devices like switches and routers is a good idea. Do not choose either of the members of the HA cluster. Nor should you select someone's workstation. It is also important to select ping nodes that reflect the connectivity of your HA nodes. If you wish to monitor the connectivity of two interfaces, it is wise to select a ping node for each interface, that is reachable exclusively from said interface. Consult
for a graphical representation of this idea. Set
to on or off.
will only operate if
has been configured to something other than legacy. In , set the
option to on or off like so: auto_failback on
or auto_failback off
Configure your
to start . Add a line like the following to
(assuming your compile PREFIX is /usr): respawn hacluster /usr/lib/heartbeat/ipfail
to . The ping nodes can be added to the cluster by using a line like the following: ping pnode1 pnode2 pnodeN
Simply replace pnode1, pnode2, ... pnodeN with the IP addresses of your ping nodes. Ensure that the above configuration directives are added to the
on both members of the cluster, and that they are identical. NOTE: You will want to check on the availability of the
prior to using them. If you cannot ping them from both of the HA nodes, they are useless. One important aspect of configuring the
file for a machine which has multiple Ethernet interfaces is to know how
selects which interface will wind up supporting the
that are configured in . After all, no interface was specified in the
decides which interface will be used by looking at the routing table. It tries to select the lowest cost route to the IP address to be taken over. In the case of a tie, it chooses the first route found. For most configurations this means the default route will be least preferred. If you don't specify a netmask for the IP address in the
file, the netmask associated with the selected route will be used. Similarly, if an interface is not specified, then the virtual IP address will be added to the interface associated with the selected route. If the broadcast address is omitted then the highest address in the subnet is used.
determines your authentication keys. There are three types of authentication methods available: crc, md5, and sha1. &Well, which should I use?&, you ask. Since this document is called &Getting Started&, we'll keep it simple...... If your
runs over a secure network, such as the crossover cable in our example, you'll want to use crc. This is the cheapest method from a resources perspective. If the network is insecure, but you're either not very paranoid or concerned about minimizing CPU resources, use md5. Finally, if you want the best authentication without regard for CPU resources, use sha1. It's the hardest to crack. The format of the file is as follows: auth &number&
&number& &authmethod& [&authkey&]So, for sha1, a sample /etc/ha.d/authkeys could be: auth 1
1 sha1 key-for-sha1-any-text-you-wantFor md5, you could use the same as the above, but replace &sha1& with &md5&. Finally, for crc, a sample might be: auth 2
2 crcWhatever index you put after the keyword auth must be found below in the keys listed in the file. If you put &auth 4&, then there must be a &4 signaturetype& line in the list below. Make sure its permissions are safe, like 600. And &any text you want& is not quite right. There's a limit to the number of characters you can use. That's it! From Red Hat, or other distributions which use /etc/init.d startup files, simply type /etc/init.d/heartbeat&start on both nodes. I would recommend starting on the system master (in our example linuxha1) first. If you want
to run on startup, what to do will differ on your distribution. You may need to place links to the startup script in the appropriate init level directories, but the
versions will do this for you. I have
start at its default sequential priority (75, which means it starts after services 74 and lower and before services with priority 76-99), end at its default sequential priority (05), and only care about the 0(halt), 6(reboot), 3(text-only), 5(X) run levels. So, if I had to do it by hand, I'd need to type in the following (as root, of course): cd /etc/rc.d/rc0. ln -s ../init.d/heartbeat K05heartbeat'''
cd /etc/rc.d/rc3. ln -s ../init.d/heartbeat S75heartbeat'''
cd /etc/rc.d/rc5. ln -s ../init.d/heartbeat S75heartbeat'''
cd /etc/rc.d/rc6. ln -s ../init.d/heartbeat K05heartbeat'''
The last time I ran Slackware, there was no /etc/rc.d/init.d directory (may have changed by now) and to do the same thing, I would have placed in /etc/rc.d/rc.local: /etc/ha.d/heartbeat start
***This assumes you copy the file ha.rc to /etc/ha.d/heartbeat. If you can't find /etc/rc.d/init.d with your distribution and you're unsure of how processes start, you can use the rc.local method. But you're on your own for shutdown, I just don't remember... Note: If you use the watchdog function, you'll need to load its module at bootup as well. You can put the following command at the bottom of the /etc/rc.d/rc.sysinit file: /sbin/insmod softdog
For the rc.local method, just put the same line right above where you start . Once you've started , take a peek at your log file (default is /var/log/ha-log) before testing it. If all is peachy, the service owner's log (linuxha1 in our example) should look something like this: heartbeat: _13:52:22 info: Neither logfile nor logfacility found.
heartbeat: _13:52:22 info: Logging defaulting to /var/log/ha-log
heartbeat: _13:52:22 info: **************************
heartbeat: _13:52:22 info: Configuration validated. Starting heartbeat 0.4.9f
heartbeat: _13:52:22 info: nice_failback is in effect.
heartbeat: _13:52:22 info: heartbeat: version 0.4.9f
heartbeat: _13:52:22 info: Heartbeat generation: 17
heartbeat: _13:52:22 info: Starting serial heartbeat on tty /dev/ttyS0 (19200 baud)
heartbeat: _13:52:22 info: UDP Broadcast heartbeat started on port 694 (694) interface eth1
heartbeat: _13:52:23 info: pid 28140 locked in memory.
heartbeat: _13:52:23 info: pid 28137 locked in memory.
heartbeat: _13:52:23 info: pid 28139 locked in memory.
heartbeat: _13:52:23 notice: Using watchdog device: /dev/watchdog
heartbeat: _13:52:23 info: pid 28141 locked in memory.
heartbeat: _13:52:23 info: Local status now set to: 'up'
heartbeat: _13:52:23 info: pid 28138 locked in memory.
heartbeat: _13:52:23 info: pid 28134 locked in memory.
heartbeat: _13:52:25 info: Link linuxha1.linux-ha.org:eth1 up.
heartbeat: _13:53:23 WARN: node linuxha2.linux-ha.org: is dead
heartbeat: _13:53:23 info: Dead node linuxha2.linux-ha.org held no resources.
heartbeat: _13:53:23 info: Resources being acquired from linuxha2.linux-ha.org.
heartbeat: _13:53:23 info: Local status now set to: 'active'
heartbeat: _13:53:23 info: Running /etc/ha.d/rc.d/status status
heartbeat: _13:53:23 info: /usr/lib/heartbeat/mach_down: nice_failback: acquiring foreign resources
heartbeat: _13:53:23 info: mach_down takeover complete.
heartbeat: _13:53:23 info: mach_down takeover complete for node linuxha2.linux-ha.org.
heartbeat: _13:53:23 info: Acquiring resource group: linuxha1.linux-ha.org 192.168.85.3 datadisk::drbd0 datadisk::drbd1 mirror
heartbeat: _13:53:23 info: Running /etc/ha.d/resource.d/IPaddr 192.168.85.3 start
heartbeat: _13:53:23 info: /sbin/ifconfig eth0:0 192.168.85.3 netmask 255.255.255.0
broadcast 192.168.85.255
heartbeat: _13:53:23 info: Sending Gratuitous Arp for 192.168.85.3 on eth0:0 [eth0]
heartbeat: _13:53:23 /usr/lib/heartbeat/send_arp eth0 192.168.85.3
192.168.85.3 ffffffffffff
heartbeat: _13:53:24 info: Running /etc/ha.d/resource.d/datadisk drbd0 start
heartbeat: _13:53:24 info: Running /etc/ha.d/resource.d/datadisk drbd1 start
heartbeat: _13:53:25 info: Running /etc/ha.d/resource.d/mirror
heartbeat: _13:53:25 /usr/lib/heartbeat/send_arp eth0 192.168.85.3
192.168.85.3 ffffffffffff
heartbeat: _13:53:26 info: Resource acquisition completed.
heartbeat: _13:53:28 /usr/lib/heartbeat/send_arp eth0 192.168.85.3
192.168.85.3 ffffffffffff
heartbeat: _13:53:30 /usr/lib/heartbeat/send_arp eth0 192.168.85.3
192.168.85.3 ffffffffffff
heartbeat: _13:53:32 /usr/lib/heartbeat/send_arp eth0 192.168.85.3
192.168.85.3 ffffffffffff
heartbeat: _13:53:33 info: Local Resource acquisition completed. (none)
heartbeat: _13:53:33 info: local resource transition completed.
heartbeat: _13:56:30 info: Link linuxha2.linux-ha.org:eth1 up.
heartbeat: _13:56:30 info: Status update for node linuxha2.linux-ha.org: status up
heartbeat: _13:56:30 info: Running /etc/ha.d/rc.d/status status
heartbeat: _13:56:30 info: Status update for node linuxha2.linux-ha.org: status active
heartbeat: _13:56:30 info: remote resource transition completed.
heartbeat: _13:56:30 info: Running /etc/ha.d/rc.d/status status
heartbeat: _13:56:31 info: Link linuxha2.linux-ha.org:/dev/ttyS0 up.NOTE: Your log may differ depending on when you started
on linuxha2!!! I started
on the linuxha2 @13:56:30... OK, now try to ping your cluster's IP (192.168.85.3 in the example). If this works,
to it and verify you're on linuxha1. Next, make sure your services are tied to the .3 address. Bring up Netscape and type in 192.168.85.3 for the URL. For Samba, try to map the drive &//192.168.85.3/test& assuming you set up a share called &test&. See Samba docs to get that going. As an aside, however, you'll want to use the &netbios name& parameter to have your Samba share listed under the cluster name and not the hostname of your cluster member! NOTE: If you can't bring up the service IP address and you get ha-log entries similar to this: SIOCSIFADDR: No such device
SIOCSIFFLAGS: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
SIOCSIFFLAGS: No such device
SIOCADDRT: No such device
It may mean that you need to enable IP aliasing in your kernel build. Check /usr/src/linux/.config for &CONFIG_IP_ALIAS=y& if you don't have it, you'll have the line &CONFIG_IP_ALIAS&is&not&set&. Rebuild your kernel with IP aliasing enabled. If this all works, you've got availability. Now let's see if we have High Availability
Take down linuxha1. Kill power, kill , whatever you have the stomach for, but don't just yank both the serial and eth1 heartbeat cables. If you do that, you'll have services running on both nodes and when you re-connect the heartbeat, a bit of chaos.... Now ping the cluster IP. Approximately 5-10 seconds later it should start responding again. Telnet again and verify you're on linuxha2. If it happens but takes more like 30 seconds, something is wrong. If you get this far, it's probably working, but you should probably check all your heartbeats, too. First, check your serial heartbeat. Unplug the crossover cable from your eth1 NIC that you're using for your bcast heartbeat. Wait about 10 seconds. Now, look at /var/log/ha-log on linuxha2 and make sure there's no line like this: _12:40:58 node linuxha1.linux-ha.org: is dead
If you get that, your serial heartbeat isn't working and your second node is taking over. To avoid any problems, shut down
on the first node, then test your null modem cable. Run the above serial tests again. If your log is clean, great. Re-connect the crossover cable. Once that's done, disconnect the serial cable, wait 10 seconds and check the linuxha2 log again. If it's clean, congrats! If not, you can check /var/log/ha-log and /var/log/ha-debug for more clues. Your cable diagram should be as follows: Connector AConnector BPin #Pin #1326314257687485
* 以上用户言论只代表其个人观点，不代表CSDN网站的观点或立场
访问：27058次
排名：千里之外
原创：15篇
(2)(1)(6)(6)