关于powermill视频教程4轴旋转加工的各...

来源：蜘蛛抓取(WebSpider) 时间：2011-10-24 09:46 标签： powermill
The page is temporarily unavailable
nginx error!
The page you are looking for is temporarily unavailable.
Please try again later.
Website Administrator
Something has triggered an error on your
This is the default error page for
nginx that is distributed with
It is located
/usr/share/nginx/html/50x.html
You should customize this error page for your own
site or edit the error_page directive in
the nginx configuration file
/etc/nginx/nginx.conf.The page is temporarily unavailable
nginx error!
The page you are looking for is temporarily unavailable.
Please try again later.
Website Administrator
Something has triggered an error on your
This is the default error page for
nginx that is distributed with
It is located
/usr/share/nginx/html/50x.html
You should customize this error page for your own
site or edit the error_page directive in
the nginx configuration file
/etc/nginx/nginx.conf.The page is temporarily unavailable
nginx error!
The page you are looking for is temporarily unavailable.
Please try again later.
Website Administrator
Something has triggered an error on your
This is the default error page for
nginx that is distributed with
It is located
/usr/share/nginx/html/50x.html
You should customize this error page for your own
site or edit the error_page directive in
the nginx configuration file
/etc/nginx/nginx.conf.The page is temporarily unavailable
nginx error!
The page you are looking for is temporarily unavailable.
Please try again later.
Website Administrator
Something has triggered an error on your
This is the default error page for
nginx that is distributed with
It is located
/usr/share/nginx/html/50x.html
You should customize this error page for your own
site or edit the error_page directive in
the nginx configuration file
/etc/nginx/nginx.conf.总共14187条微博动态微博: 昨天&18:30&: 昨天&16:55&: 昨天&15:43&: 昨天&11:55&: 昨天&09:34&: 前天&17:50&: 前天&12:17&: 前天&11:03&: 前天&09:34&: 3&天前&: 3&天前&: 3&天前&: 3&天前&: 4&天前&: 4&天前&: 4&天前&: 5&天前&: 6&天前&: 6&天前&: 6&天前&: 6&天前&: 7&天前&: 7&天前&: 7&天前&: 7&天前&:
查看: 284|回复: 0
求助（购）：木工4轴加工（主轴旋转，A或B轴）后处理
本帖最后由 artistf 于
21:31 编辑
现有木工雕刻机1325一台，主轴可在XZ面旋转正负90度。控制系统为新代（10MB或EZ4）
2012做好刀路输出（Fanuc或西门子5轴后处理）去掉多余的行后系统不报错可运行，但发现主轴旋转导致的XZ位置变化没有被考虑进去。导致实际主轴走的范围很小。问过技术人员及新代的销售代理，系统内没有设定旋转半径之类的参数。只能通过软件做路径时特殊处理，但现在没有合适的后处理。所做刀路为平行精加工（朝向直线）。请问哪位朋友有经验？如何解决此问题呢？谢谢。
打赏列表共打赏了0次
还木有人打赏~
站长推荐 /1
UG NX11.0安装包大小：7.1G
下载速度较快，建议在用网不频繁时间段下载，以免影响你的工作。
UG ＮＸ11.0关键词：体验、新功能、解决安装问题
Powered by

我要回帖

更多关于 powermill 的文章

 

随机推荐