查看: 427|回复: 5
求助 TTL刷机问题，高手们帮我看看。
本帖最后由 lingxtx411 于
09:23 编辑
新手不会弄，求大神帮我分析一下，看别人的教程说几个选项那里按4刷机，
我遇到的问题是路由器通上电后就这样刷刷的一大溜英文出来了，按任何键都没反应，搞了两天，用TTL可以刷进原厂固件，其他的固件都刷不进去，谁知道是什么原因？
U-Boot 1.1.3 (Jun 16 2016 - 20:48:53)
Board: Ralink APSoC DRAM:&&64 MB
relocate_code Pointer at: 83fb8000
flash manufacture id: ef, device id 40 17
find flash: W25Q64BV
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5&-&None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Jun 16 2016&&Time:20:48:53
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 575 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
& &1: Load system code to SDRAM via TFTP.
& &2: Load system code then write to Flash via TFTP.
& &3: Boot system code via Flash (default).
& &4: Entr boot command line interface.
& &7: Load Boot Loader code then write to Flash via Serial.
& &9: Load Boot Loader code then write to Flash via TFTP.
You choosed 3
3: System Boot system code via Flash.
## Booting image at bc050000 ...
& &Image Name:& &ANTBANG_A5
& &Image Type:& &MIPS Linux Kernel Image (lzma compressed)
& &Data Size:& & 1658652 Bytes =&&1.6 MB
& &Load Address:
& &Entry Point:&&
& &Verifying Checksum ... OK
& &Uncompressing Kernel Image ... OK
## Transferring control to Linux (at address 8000
LINUX started...
THIS IS ASIC
Linux version 3.10.14+ (root@l) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-99) ) #8 Sat Aug 13 23:00:49 CST 2016
The CPU feqenuce set to 575 MHz
CPU0 revision is:
(MIPS 24KEc)
Software DMA cache coherency
Determined physical RAM map:
Initrd not found or empty - disabling initrd
Zone ranges:
&&Normal& &[mem 0xx03ffffff]
Movable zone start for each node
Early memory node ranges
&&node& &0: [mem 0xx03ffffff]
Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on.&&Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Writing ErrCtl register=
Readback ErrCtl register=
Memory: 5k available (3353k kernel code, 5572k reserved, 1106k data, 212k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 382.46 BogoMIPS (lpj=764928)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab &bio-0& at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
U(order: 0, 4096 bytes)
NET: Registered protocol family 1
MTK/Ralink EHCI/OHCI init.
squashfs: version 4.0 () Phillip Lougher
jffs2: version 2.2. (NAND) (SUMMARY)&&(LZMA) (RTIME) (CMODE_PRIORITY) (c)
Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 117
io scheduler noop registered (default)
driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial825 = 20) is a 16550A
Ralink gpio driver initialized
brd: module loaded
flash manufacture id: ef, device id 40 17
W25Q64BV(ef ) (8192 Kbytes)
mtd .name = raspi, .size = 0xM) .erasesize = 0xK) .numeraseregions = 0
Creating 5 MTD pa : &ALL&
0x-0x : &Bootloader&
0x-0x : &Config&
0x-0x0 : &firmware&
0xf5c-0x0 : &rootfs&
mtd: partition &rootfs& must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition &rootfs_data& created automatically, ofs=0x690000, len=0x160000
0x-0x0 : &rootfs_data&
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
rdm_major = 253
netif_napi_add() called with weight 128 on device eth0
GMAC1_MAC_ADRH -- : 0x0000001c
GMAC1_MAC_ADRL -- : 0xa30429b0
Ralink APSoC Ethernet Driver Initilization. v3.1&&384 rx/tx descriptors allocated, mtu = 1500!
NAPI enable, Tx Ring = 384, Rx Ring = 384
GMAC1_MAC_ADRH -- : 0x0000001c
GMAC1_MAC_ADRL -- : 0xa30429b0
PROC INIT OK!
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-platform: EHCI generic platform driver
******MT7628 mtk phy
*****run project phy.
FM_OUT value: u4FmOut = 0(0x)
FM_OUT value: u4FmOut = 141(0x0000008D)
FM detection done! loop = 1
SR calibration value u1SrCalVal = 6
*********Execute mt7628_phy_init!!
ehci-platform ehci-platform: EHCI Host Controller
ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
ehci-platform ehci-platform: irq 18, io mem 0x101c0000
ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
*********Execute mt7628_phy_init!!
ohci-platform ohci-platform: Generic Platform OHCI Controller
ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
ohci-platform ohci-platform: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usb-storage
u32 classifier
nf_conntrack version 0.5.0 (936 buckets, 3744 max)
ip_tables: (C)
Netfilter Core Team
Type=Linux
---ANTBANG A5 GPIO INIT---
----------------------------
--------igd inited----------
----------------------------
TCP: cubic registered
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
registered taskstats version 1
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
procd: Console is alive
procd: - preinit -
Raeth v3.1 (NAPI
,SkbRecycle)
phy_tx_ring = 0x035bc000, tx_r = 0x035be000, rx_ring0 = 0xa35be000
GMAC1_MAC_ADRH -- : 0x0000001c
GMAC1_MAC_ADRL -- : 0xa30429b0
RT305x_ESW: Link Status Changed
/etc/preinit: line 1: netmsg: not found
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
kmod: ran 1 iterations
jffs2: notice: (303) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 9 of xref (0 dead, 3 orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
jffs2 is ready
jffs2: notice: (300) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 9 of xref (0 dead, 3 orphan) found.
switching to overlay
ra2880stop()...Done
Free TX/RX Ring Memory!
procd: - early -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
tntfs: module license 'Commercial. For support email .' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver
[Flags: R/W MODULE].
Tuxera FAT 12/16/32 driver version
[Flags: R/W MODULE].
Built against headers 3.10.14+ #73 Thu Feb 18 11:57:28 CST 2016 mips
Running on kernel 3.10.14+ #8 Sat Aug 13 23:00:49 CST 2016 mips
WARNING: Running kernel does not match configured kernel headers the driver was built with!&&The driver needs to be rebuilt with the correct kernel headers!
Tuxera exFAT driver version
[Flags: R/W MODULE].
Built against headers 3.10.14+ #73 Thu Feb 18 11:57:28 CST 2016 mips
Running on kernel 3.10.14+ #8 Sat Aug 13 23:00:49 CST 2016 mips
Tuxera HFS+ driver regiester url hooks finish
Raeth v3.1 (NAPI
,SkbRecycle)
phy_tx_ring = 0x, tx_ring = 0xa3770000
phy_rx_ring0 = 0x, rx_ring0 = 0xa3772000
GMAC1_MAC_ADRL -- : 0xa30429b0
RT305x_ESW: Link Status Changed
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
--------&fdb_create, 470!!!
nl socket is null !
br-lan: port 1(eth0.1) entered forwarding state
br-lan: port 1(eth0.1) entered forwarding state
--------&fdb_create, 470!!!
nl socket is null !
nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
efuse_probe: efuse =
[IPC:00369]:ipc server success, path:/tmp/ipc_path_disk, sock:3
tssi_1_target_pwr_g_band = 35
device ra0 entered promiscuous mode
br-lan: port 2(ra0) entered forwarding state
br-lan: port 2(ra0) entered forwarding state
procd: - init complete -
device ra1 entered promiscuous mode
--------&fdb_create, 470!!!
host_ugrp_update[1435]port id err 8, need fix
RT305x_ESW: Link Status Changed
[IPC:00198]:connect OK,socket=4
device eth0.2 entered promiscuous mode
br-lan: port 4(eth0.2) entered forwarding state
br-lan: port 4(eth0.2) entered forwarding state
main[102]:reset start
wps_init[12]:wps init
resetd_init[37]:flag:38
br-lan: port 1(eth0.1) entered forwarding state
RT305x_ESW: Link Status Changed
br-lan: port 2(ra0) entered forwarding state
procd: Instance log::instance1 s in a crash loop 6 crashes, 0 seconds since last crash
br-lan: port 4(eth0.2) entered forwarding state
net_ratelimit: 6 callbacks suppressed
Jan&&1 00:00:24 miniupnpd[1153]: HTTP listening on port 30108
Jan&&1 00:00:24 miniupnpd[1153]: Listening for NAT-PMP traffic on port 5351
4是进入命令行模式，用命令行刷机，3是正常启动
关键是我这个没办法选择4，按任何键没反应。&
4是进入命令行模式，用命令行刷机，3是正常启动
关键是我这个没办法选择4，按任何键没反应。
请问一下，这个机器的波特率是多少呀，我试了半天都不行& &&&
波特率 57600&
请问一下，这个机器的波特率是多少呀，我试了半天都不行
波特率 57600
搞了两天，用TTL可以刷进原厂固件，其他的固件都刷不进去，谁知道是什么原因？
Powered by||||||||||
||||||||||
查看: 847|回复: 2
求助高手帮我看看日立50寸等离子电视是那点的问题。。。
阅读权限20
在线时间 小时
注册家电维修技术论坛，与同行畅聊维修技术，享更多技术论坛功能。
才可以下载或查看，没有帐号？
本机问题1 通电开机亮一下就熄灭了。绿灯一直闪烁。屏亮的时候画面如图一。。亮一下就熄灭了。。看看是电源的问题。。还是Y板跟缓冲板的问题引起保护了。。。
阅读权限55
在线时间 小时
我遇见过Y板跟缓冲板问题的。。。
阅读权限45
在线时间 小时
是缓冲板的问题，淘宝网上有。
( 鄂ICP备号-1 )&&
Powered by Discuz! X3.2
Comsenz Inc.
CopyRight ©
电子邮箱：
QQ：8794149
官方网址：
Qiji. All Rights Reserved
Wuhan Qiji Technology Co., Ltd.武汉奇迹科技有限公司版权所有求高手帮我看看_java吧_百度贴吧
&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&签到排名：今日本吧第个签到，本吧因你更精彩，明天继续来努力！
本吧签到人数：0成为超级会员，使用一键签到本月漏签0次！成为超级会员，赠送8张补签卡连续签到：天&&累计签到：天超级会员单次开通12个月以上，赠送连续签到卡3张
关注：563,198贴子：
求高手帮我看看收藏
最近在看传智播课的方老师的web 开发的视频，为什么有个我敲了一样的代码 测试会报错了java.lang.RuntimeException: org.dom4j.DocumentException: E:\myeclipse\MyEclipse%2010\Workspaces\MyEclipse%2010\day09_user\WebRoot\WEB-INF\classes\users.xml (系统找不到指定的路径。) Nested exception: E:\myeclipse\MyEclipse%2010\Workspaces\MyEclipse%2010\day09_user\WebRoot\WEB-INF\classes\users.xml (系统找不到指定的路径。)上面找到的路径与实际的路径（E:\myeclipse\MyEclipse 10\Workspaces\MyEclipse 10\day09_user\src\users.xml）不一致，怎么办？
java培训---美国上市公司出品,入学签订就业协议,名企疯抢达内学员.java,O基础小班授课,java专家领衔授课,免费试听,满意后付款!
因为你的路径中包含了
那么明白的错
登录百度帐号推荐应用
为兴趣而生，贴吧更懂你。或2009年 总版技术专家分年内排行榜第四
2009年2月 总版技术专家分月排行榜第一2009年1月 总版技术专家分月排行榜第一2008年11月 总版技术专家分月排行榜第一2008年10月 总版技术专家分月排行榜第一2008年9月 总版技术专家分月排行榜第一2008年8月 总版技术专家分月排行榜第一2008年7月 总版技术专家分月排行榜第一2008年6月 总版技术专家分月排行榜第一2008年5月 总版技术专家分月排行榜第一2008年4月 总版技术专家分月排行榜第一
2009年 总版技术专家分年内排行榜第四
2009年2月 总版技术专家分月排行榜第一2009年1月 总版技术专家分月排行榜第一2008年11月 总版技术专家分月排行榜第一2008年10月 总版技术专家分月排行榜第一2008年9月 总版技术专家分月排行榜第一2008年8月 总版技术专家分月排行榜第一2008年7月 总版技术专家分月排行榜第一2008年6月 总版技术专家分月排行榜第一2008年5月 总版技术专家分月排行榜第一2008年4月 总版技术专家分月排行榜第一
本帖子已过去太久远了，不再提供回复功能。