当前位置： &
求翻译：SKLDR is missing prass ctrl+alt+del是什么意思？
SKLDR is missing prass ctrl+alt+del
问题补充：
skldr是缺少prass CTRL + ALT + DEL
skldr缺失国际新闻社按ctrl+alt+del键
SKLDR错过prass ctrl+alt+del
缺少新闻社 ctrl + alt + del SKLDR
SKLDR 是遗失的 prass ctrl+alt+del
我来回答：
参考资料：
* 验证码：
登录后回答可以获得积分奖励，并可以查看和管理所有的回答。 |
我要翻译和提问
请输入您需要翻译的文本！NTLDR is missing
You are here:
NTLDR is Missing
Below are the full error messages that may be seen when the computer is booting.
NTLDR is Missing
Press any key to restart
Boot: Couldn't find NTLDR
Please insert another disk
NTLDR is missing
Press Ctrl Alt Del to Restart
Computer is booting from a non-bootable source
Many times this error is caused when the computer is attempting to boot from a non-bootable floppy disk or . First verify that no
or CD is in the computer, unless you are attempting to boot from a diskette.
Note: This error has also been known to occur when a
and the computer is attempting to boot from it. If you have any card reader or flash reader, make sure that no memory stick is inside the reader. Additionally, disconnect all
drives, , , , etc. from the computer.
If you are attempting to
from a floppy diskette and are receiving this error message, it is likely that the diskette does not have all the necessary files or is corrupt.
If you are attempting to install Windows XP or Windows 2000 and are receiving this error message as the computer is booting, verify that your computer
has the proper boot settings. For example, if you are attempting to run the install from the CD-ROM, make sure the CD-ROM is the first device listed in the , instead of the hard drive.
Also, when the computer is booting, you should receive the below prompt:
Press any key to boot from the CD
Important: When you see this prompt, press
on the keyboard immediately, such as the Enter or Space key. Otherwise, the computer will try booting from the hard drive and likely get the NTLDR error again.
Note: If you are not receiving the above message and your BIOS boot options are set properly, it's also possible that your CD-ROM drive may not be booting from the CD properly. Verify the jumpers are set properly on the CD-ROM drive.
Computer hard drive is not properly setup in CMOS
Verify that your computer
is properly set up in the . Improper settings can cause this error.
Corrupt NTLDR
Windows 2000 users
If your computer is using Microsoft Windows 2000 and you are encountering the NTLDR error, create the below
file on the floppy diskette drive.
[boot loader]
timeout=30
default=multi(0)disk(0)rdisk(0)partition(1)\WINNT
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINNT=&Microsoft Windows 2000 Professional& /fastdetect
Copy the NTLDR
files from another computer using the same operating system. Both of these files are located in the
directory of the primary hard drive. For example, C:\NTLDR and C:\ should be the locations of these files on many computers.
Once these files have been copied to a floppy diskette, reboot the computer and copy the NTLDR
files to the root directory of the primary hard drive. Below is an example of the commands that should be performed from the A:\& floppy drive to copy the files.
copy ntldr c:
After the above two files have been copied, remove the floppy diskette and reboot the computer.
Windows XP users
Insert the Windows XP bootable CD into the computer.
When prompted to press any key to boot from the CD, press any key on the keyboard.
Once in the Windows XP setup menu, press the &R& key to repair Windows.
Log into your Windows installation by pressing the &1& key and pressing Enter.
You will then be prompted for your administrator password. Enter that password.
Copy the below two files to the
directory of the primary hard drive. In the example below, we are copying these files from the CD-ROM drive letter, which in this case is &e.& This letter may be different on your computer.
copy e:\i386\ntldr c:\
copy e:\ c:\
Once both of these files have been successfully copied, remove the CD from the computer and reboot.
Misconfiguration with the boot.ini file
directory of the hard drive and verify that it is pointing to the correct location of your Windows operating system and that the partitions are properly defined.
Attempting to upgrade from a Windows 95, 98, or ME computer that is using FAT32
You may receive this error message when trying to upgrade to Windows 2000 or Windows XP from , , or
running . If so, try the below recommendations.
Boot the computer with a Windows 95, Windows 98 or Windows ME .
At the A:\& prompt, type sys c: and press Enter.
After pressing Enter, you should receive the &System Transferred& message. Once this has been completed, remove the floppy diskette and reboot the computer.
New hard drive being added
If you are attempting to add a new
to the computer, make sure the drive is a blank drive. Adding a new hard drive to a computer that already has Windows installed on it may cause the NTLDR error to occur.
If you are unsure if the new drive is blank, try booting from a
and format the new hard drive.
Corrupt boot sector or master boot record
It's possible your computer's hard drive may have a corrupt boot sector or master boot record. These can be repaired through the
by running the fixboot and fixmbr commands.
Seriously corrupted version of Windows 2000 or Windows XP
If you have tried each of the above recommendations that apply to your situation and you continue to receive the NTLDR error, there may be a more serious corruption in Microsoft Windows. Therefore we would recommend .
If you are encountering this issue during your setup, you may want to completely .
Loose or Faulty IDE/EIDE hard drive cable
This issue has been known to be caused by a loose or defective / cable. If the above recommendation does not resolve your issue and your computer hard drive is using an
interface, verify the computer hard drive cable is firmly connected by disconnecting and reconnecting the cable.
If the issue continues, it is also a possibility that the computer has a faulty cable, try replacing the hard drive cable with another cable or a new cable.
Additional information
Was this page useful?
Recently added pages
Useful links联想笔记本电脑出现SKLDR is compressed Press Ctr+Alt+Del to restart ?怎么办？按了F2该咋怎？_百度知道
联想笔记本电脑出现SKLDR is compressed Press Ctr+Alt+Del to restart ?怎么办？按了F2该咋怎？
这是Win7旗舰版的系统，重装系统有这种盘卖么？
提问者采纳
读不到系统盘无法进入系统，按 Ctr+Alt+Del 重启，按了F2进入BIOS查看设置BIOS，修改第一启动项硬盘，看不到硬盘供甫垛晃艹浩讹彤番廓故障了- -！！！重装，正版盗版都有，电脑店买
提问者评价
其他类似问题
您好！为了简便快捷的解决您的疑惑，问题需要专业的工程师后台查询有关内部数据才，然后通过机器信心解决问题，建议您联系联想售后，售后电话咨询：其他问题也可以在这两个论坛比较全，Idea论坛：Think论坛：希望能帮助到您，谢谢呢。
来自团队：
为您推荐：
其他2条回答
按F2进BIOS设置，恢复出厂值保存退出试试。你是要重装供甫垛晃艹浩讹彤番廓系统吗，在里面设置光驱或USB启动，装完后改硬盘启动。我2010年买了个win7旗舰版和xp合版的10元，用着还行。
送去保修的地方弄就好了
联想笔记本电脑的相关知识
等待您来回答
下载知道APP
随时随地咨询
出门在外也不愁电脑开机时出现SKLDR is compressed ，该怎么办？进不了系统了。急！_百度知道
电脑开机时出现SKLDR is compressed ，该怎么办？进不了系统了。急！
我有更好的答案
如果你有引导光盘的话可以用光盘引导， 对系统进行覆盖。在不然的话就只能重装系统了出现“SKLDR is compressed”是因为你把系统盘给压缩了 导致系统无法正常启动
你把系统盘给压缩了！你先尝试一下能不能进DOS，可以的话从别的机器复制引导文件进去覆盖，不能进的话用带WIN PE 的维护光盘进。还不行的话用ghost光盘把原盘备份，重新格掉安个系统，再把原系统还原。
你下载的软件和内存有冲突了。你先杀一下毒，，再用360把多余的软件卸了。再清理一下。
其他类似问题
为您推荐：
电脑开机的相关知识
等待您来回答
下载知道APP
随时随地咨询
出门在外也不愁