热门比价：
> 爱普生GS6000和爱普生4910哪个好？
图片品牌爱普生爱普生型号GS60004910最低报价0()0()用户评论4分 ()4.7分 ()参数
EPSON 爱普生
Stylus Pro GS6000
大幅面打印机
高质量模式 5.8 m2/h (dpi)
质量模式 9.2 m2/h (540&720dpi)
一般模式 25.2 m2/h (720&360dpi)
打印分辨率
dpi（智能墨滴变换技术）
USB2.0（兼容1.1），1GB以太网
卷纸尺寸 最大外径170mm 最大卷纸重量 30.0kg 最大厚度 1.3mm 介质宽度 卷纸：300-1626mm
AC 100-120V/220-240V
运行（加热器工作）：680W
待机（加热器关闭）：40W（100-120V），48W（220-240V）
工作 54.79dB（A）
待机 42.79dB（A）
约184kg（不包含墨盒重量）
EPSON 爱普生
Stylus Pro 4910
大幅面打印机
大约0.5分钟（普通纸，草稿模式）
大约0.8分钟（普通纸，一般模式）
大约1.6分钟（粗面纸，一般模式）
大约2.5分钟（照片纸，优质模式）
大约3.6分钟（照片纸，超优质模式
打印分辨率
USB 2.0接口, 10Base-T/100Base-TX以太网接口
走纸方式：摩擦走纸/进纸盒容量 普通纸250页 (A4-A2/ US-C)
卷纸 宽203mm-432mm
单页纸 宽203mm-432mm
纸轴内径2英寸:最大外径 103mm
纸轴内径3英寸:最大外径 150mm
打印区域(宽度) 203mm(8&)-432mm(17&)
厚度 0.08-1.50mm
AC 100-240V 50/60Hz
运行: 52W ; 55W(使用SpectroProofer时)
睡眠: 小于8.5W
待机: 小于0.5W
小于45dB(A)
打印 863 x 1134 x 405 mm
返利咨询：
技术咨询：
商务广告：
商务合作：Epson大幅面打印机报错代码大全
数码印花技术支持：杨生，qq：
Epson GS6000 Error Codes
Maintenance Request Errors
MAINTENANCE REQUEST - 0001 - The CR scan pass counter has
reached the specified value. MAINTENANCE REQUEST - 0011 - The RTC
backup battery becomes exhausted.
MAINTENANCE REQUEST - 0111 - The date has not been set.
MAINTENANCE REQUEST - 0100 - The following two errors are
occurring simultaneously, 0001 & 0011
MAINTENANCE REQUEST - 1000 - The following two errors are
occurring simultaneously, 0001 & 0011
MAINTENANCE REQUEST - 1010 - The following two errors are
occurring simultaneously, 0011 & 0111
Service Call Errors
SERVICE CALL ERROR - 1101 - Life end of the CR MOTOR
SERVICE CALL ERROR - 1125 - Carriage home position detection
SERVICE CALL ERROR - 1133 - CR MOTOR in position time-out
SERVICE CALL ERROR - 1135 - CR ENC ASSY check error
SERVICE CALL ERROR - 1136 - CR MOTOR step-out error
SERVICE CALL ERROR - 1137 - CR servo parameter error
SERVICE CALL ERROR - 1223 - PF ENCODER ASSY check error
SERVICE CALL ERROR - 1225 - PF MOTOR in position time-out
SERVICE CALL ERROR - 1227 - PF MOTOR step-out error
SERVICE CALL ERROR - 1228 - PF servo parameter error
SERVICE CALL ERROR - 131B - Head driver (transmission gate)
overheat error
SERVICE CALL ERROR - 1700 - Print position error
SERVICE CALL ERROR - 1900 - HEATER CONT BOARD ASSY serial
connection failure
SERVICE CALL ERROR - 1902 - Over Temp PRE HEATERS(64) on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1903 - Over Temp PLATEN HEATER(64) on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1904 - Over Temp AFTER HEATER(64) on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1905 - Over Temp PRE HEATERS(64) on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1906 - Over Temp PLATEN HEATER(64) on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1907 - Over Temp AFTER HEATER(64) on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1908 - An abnormal voltage of the heater on
the HEATER CONT BOARD ASSY
SERVICE CALL ERROR - 1909 - Comms Failure HEATER CONT BOARD ASSY
and SUB-B/C BOARD
SERVICE CALL ERROR - 1910 - Under Temp PRE HEATERS(64) on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1911 - Under Temp PLATEN HEATER on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1912 - Under Temp AFTER HEATER on the
HEATER RELAY BOARD ASSY
SERVICE CALL ERROR - 1920 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 1 failure
SERVICE CALL ERROR - 1921 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 2 failure
SERVICE CALL ERROR - 1922 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 3 failure
SERVICE CALL ERROR - 1923 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 4 failure
SERVICE CALL ERROR - 1924 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 5 failure
SERVICE CALL ERROR - 1925 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 6 failure
SERVICE CALL ERROR - 1926 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 7 failure
SERVICE CALL ERROR - 1927 - HEATER CONT BOARD ASSY-SUB TANK
SENSOR 8 failure
SERVICE CALL ERROR - 1A23 - RTC analysis error
SERVICE CALL ERROR - 1A26 - RTC communication error
SERVICE CALL ERROR - 1A37 - Head thermistor error
SERVICE CALL ERROR - 1A38 - Transistor thermistor error
SERVICE CALL ERROR - 1A39 - Head error
SERVICE CALL ERROR - 1A40 - MAIN BOARD ASSY IC2 error
SERVICE CALL ERROR - 1A41 - Head rank ID input error
SERVICE CALL ERROR - 2000 - NVRAM error
SERVICE CALL ERROR - 2002 - SDRAM error
SERVICE CALL ERROR - 2003 - Boot program sum error
SERVICE CALL ERROR - 200A - Program loading error
SERVICE CALL ERROR - 200B - Internal insufficient memory
SERVICE CALL ERROR - 200C - Servo interrupt watchdog time-out
SERVICE CALL ERROR - 200D - System interrupt watchdog timeout
SERVICE CALL ERROR - 200E - Unknown NMI
SERVICE CALL ERROR - 3000 - AC power shut-off
SERVICE CALL ERROR - FXXX - CPU-related error
Epson 11880 Error Codes
Maintenance Request Errors
MAINTENANCE REQ - 0001 - The counter of waste ink
at borderless printing has reached the specified value.
MAINTENANCE REQ - 0002 - The CR scan pass counter
has reached the specified value.
MAINTENANCE REQ - 0008 - The RTC backup battery
becomes exhausted.
MAINTENANCE REQ - 0040 - The pump counter has
reached the specified value.
MAINTENANCE REQ - 0080 - The date has not been
MAINTENANCE REQ - 0100 - The RTC backup battery
power has temporarily dropped.
MAINTENANCE REQ - 0088 - The RTC backup battery
becomes exhausted and the date has not been set
Service Request Errors
SERVICE REQ - 1101 - Life end of the Ink Tube
SERVICE REQ - 1125 - Carriage home position
detection error
SERVICE REQ - 1133 - The CR Motor in position
time-out error
SERVICE REQ - 1135 - CR Encoder check error
SERVICE REQ - 1136 - CR Motor Step-out error
SERVICE REQ - 1137 - CR servo parameter error
SERVICE REQ - 1223 - PF Encoder check error
SERVICE REQ - 1225 - The PF Motor in position
time-out error
SERVICE REQ - 1227 - PF Motor Step-out error
SERVICE REQ - 1228 - PF servo parameter error
SERVICE REQ - 1400 - Pressure failure error
SERVICE REQ - 1410 - Pump motor drive timeover
SERVICE REQ - 1430 - Cartridge Holder
Maintenance
SERVICE REQ - 1434 - Ink cover unlock error
SERVICE REQ - 1435 - Cap HP detection error
SERVICE REQ - 1436 - Select valve HP detection
SERVICE REQ - 1437 - Cap motor drive timeover
SERVICE REQ - 1441 - Pressure motor 1 acceleration
SERVICE REQ - 1442 - Pressure motor 2 acceleration
SERVICE REQ - 1443 - Pressure motor 3 acceleration
SERVICE REQ - 1461 - Pressure motor 1 lock
SERVICE REQ - 1462 - Pressure motor 2 lock
SERVICE REQ - 1463 - Pressure motor 3 lock
SERVICE REQ - 1471 - Pessure motor 1 reverse
detection error
SERVICE REQ - 1472 - Pressure motor 2 reverse
detection error
SERVICE REQ - 1473 - Pressure motor 3 reverse
detection error
SERVICE REQ - 1511 - APG motor drive timeover
SERVICE REQ - 1536 - Pressurizing reset failure
SERVICE REQ - 1700 - Print position error
SERVICE REQ - 1800 - AID voltage error
SERVICE REQ - 2000 - NVRAM error
SERVICE REQ - 2002 - SDRAM error
SERVICE REQ - 2003 - BOOT program sum error
SERVICE REQ - 3000 - AC power shut-off
SERVICE REQ - 131B - Head driver (transmission
gate) overheat error
SERVICE REQ - 150C - PG HP detection error
SERVICE REQ - 16A0 - Cap unit status error 1
SERVICE REQ - 16A1 - Cap unit status error 2
SERVICE REQ - 16B0 - Cap HP detection retry
SERVICE REQ - 1A23 - RTC analysis error
SERVICE REQ - 1A26 - RTC communication error
SERVICE REQ - 1A37 - Head thermistor error
SERVICE REQ - 1A38 - Transistor thermistor
SERVICE REQ - 1A39 - Head error
SERVICE REQ - 1A40 - Main board IC2 error
SERVICE REQ - 1A41 - Head rank ID input error
SERVICE REQ - 200A - Program loading error
SERVICE REQ - 200B - Internal insufficient memory
SERVICE REQ - 200C - Servo interrupt watchdog
time-out error
SERVICE REQ - 200D - System interrupt watchdog
time-out error
SERVICE REQ - 200E - Unknown NMI
SERVICE REQ - DXXX - Debug error
SERVICE REQ - FXXX - CPU-related error
SERVICE REQ - F000 - CPU-related error
Error Codes
Maintenance Request Errors
MAINTENANCE REQ - 0002 - The CR scan pass counter
has come near the specified life.
MAINTENANCE REQ - 0008 - The RTC backup battery
becomes exhausted
MAINTENANCE REQ - 0010 - Communication with the AID
Board is not established.
MAINTENANCE REQ - 0040 - The pump counter has come
near the specified life.
MAINTENANCE REQ - 0080 - The date has not been
MAINTENANCE REQ - 0800 - Cartridge waste ink pad
near end of life
MAINTENANCE REQ - 1000 *1 - Ink Selector near end
MAINTENANCE REQ - 4000 - It detects twice in a row
that all the nozzles are clogging.
MAINTENANCE REQ - 0088 - The RTC backup battery
becomes exhausted and the date has not been set.
Service Request Errors
SERVICE REQ - 1101 - CR life error
SERVICE REQ - 1125 - CR HP detection error
SERVICE REQ - 1138 - Over current error
SERVICE REQ - 113A - Overload error
SERVICE REQ - 113B - Over speed error
SERVICE REQ - 113C - Reversing error
SERVICE REQ - 113D - Driving time-out error
SERVICE REQ - 113E - Velocity deviation error
SERVICE REQ - 113F - Lock error
SERVICE REQ - 122A - Overload error
SERVICE REQ - 122B - Over speed error
SERVICE REQ - 122C - Reversing error
SERVICE REQ - 122D - Driving time-out error
SERVICE REQ - 122E - Velocity deviation error
SERVICE REQ - 122F - Lock error
SERVICE REQ - 131B - Head driver (transmission
gate) overheat error
SERVICE REQ - 13F0 - ICL operation error
SERVICE REQ - 1411 - Select error
SERVICE REQ - 1412 - Pump life error
SERVICE REQ - 1419 - Pump release error
SERVICE REQ - 141A - Overload error
SERVICE REQ - 141B - Over speed error
SERVICE REQ - 141C - Reversing error
SERVICE REQ - 141D - Driving time-out error
SERVICE REQ - 141E - Velocity deviation error
SERVICE REQ - 141F - Lock error
SERVICE REQ - 1427 - CSIC destination setting
SERVICE REQ - 1428 - Ink holder Board Assy
SERVICE REQ - 1430 - Holder ink pad error
SERVICE REQ - 1431 - Ink selector life error
SERVICE REQ - 1434 - IC cover unlock error
SERVICE REQ - 1438 - Maintenance tank error
SERVICE REQ - 1439 - Cap error
SERVICE REQ - 143A - Overload error
SERVICE REQ - 143B - Over speed error
SERVICE REQ - 143C - Reversing error
SERVICE REQ - 143D - Driving time-out error
SERVICE REQ - 143E - Velocity deviation error
SERVICE REQ - 143F - Lock error
SERVICE REQ - 144A - Overload error
SERVICE REQ - 144B - Over speed error
SERVICE REQ - 144C - Reversing error
SERVICE REQ - 144D - Driving time-out error
SERVICE REQ - 144E - Velocity deviation error
SERVICE REQ - 144F - Lock error
SERVICE REQ - 1489 - Wiper error
SERVICE REQ - 148A - Overload error
SERVICE REQ - 148B - Over speed error
SERVICE REQ - 148C - Reversing error
SERVICE REQ - 148D - Driving time-out error
SERVICE REQ - 148E - Velocity deviation error
SERVICE REQ - 148F - Lock error
SERVICE REQ - 1494 - Ink selector error
SERVICE REQ - 1496 - Ink selector sensor error
SERVICE REQ - 1497 - Switching time-out error
SERVICE REQ - 149D - Driving time-out error
SERVICE REQ - 1501 - Release motor phase detection
SERVICE REQ - 150C - PG phase detection error
SERVICE REQ - 151A - Overload error
SERVICE REQ - 151B - Over speed error
SERVICE REQ - 151C - Reversing error
SERVICE REQ - 151D - Driving time-out error
SERVICE REQ - 151E - Velocity deviation error
SERVICE REQ - 151F - Lock error
SERVICE REQ - 152A - Overload error
SERVICE REQ - 152B - Over speed error
SERVICE REQ - 152C - Reversing error
SERVICE REQ - 152D - Driving time-out error
SERVICE REQ - 152E - Velocity deviation error
SERVICE REQ - 152F - Lock error
SERVICE REQ - 1530 - Driven roller HP detection
SERVICE REQ - 1536 - Pressurizing reset error
SERVICE REQ - 1537 - Pressurizing error
SERVICE REQ - 153A - Overload error
SERVICE REQ - 153B - Over speed error
SERVICE REQ - 153C - Reversing error
SERVICE REQ - 153D - Driving time-out error
SERVICE REQ - 153E - Velocity deviation error
SERVICE REQ - 153F - Lock error
SERVICE REQ - 1540 - Cutter HP detection error
SERVICE REQ - 1541 - Cutter return error
SERVICE REQ - 1549 - Motor disconnection error
SERVICE REQ - 154A - Overload error
SERVICE REQ - 154B - Over speed error
SERVICE REQ - 154C - Reversing error
SERVICE REQ - 154D - Driving time-out error
SERVICE REQ - 154E - Velocity deviation error
SERVICE REQ - 154F - Lock error
SERVICE REQ - 1551 - Paper thickness determining
SERVICE REQ - 1561 - Paper thickness at power-on
SERVICE REQ - 1800 - AID voltage error
SERVICE REQ - 1A23 - Incorrect RTC data error
SERVICE REQ - 1A26 - RTC Access T/O error
SERVICE REQ - 1A37 - Thermistor error
SERVICE REQ - 1A38 - Transistor environmental
temperature error
SERVICE REQ - 1A39 - Head error
SERVICE REQ - 1A40 - IC22 error
SERVICE REQ - 1A41 - Head rank ID input error
SERVICE REQ - 1A50 - I2C communication error
(Between elements on ASIC and MAIN)
SERVICE REQ - 1A51 - I2C communication error
(Between elements on SUB and MAIN)
SERVICE REQ - 1A52 I- 2C communication error
(Between elements on SUB-B and MAIN)
SERVICE REQ - 1A53 - I2C communication error
(Between elements on SUB-C and MAIN)
SERVICE REQ - 2000 - NVRAM error
SERVICE REQ - 2002 - SDRAM error
SERVICE REQ - 2003 - FLASH BOOT SUM CHECK error
SERVICE REQ - 200A - F/W load error
SERVICE REQ - 200D - System interrupt watchdog
time-out error
SERVICE REQ - 200E - Unknown NMI
SERVICE REQ - 2010 - UART communication error
SERVICE REQ - 3000 - AC shut-off
SERVICE REQ - D131 - AID error
SERVICE REQ - Fxxx - CPU-related error
SERVICE REQ - Dxxx - Debug error
Spectroproofer and Auto Take-Up Error Codes
NOTE: SpectroProofer-related errors do not occur on
Epson Stylus Pro 00M//9710 because it does
not support the SpectroProofer.
Auto Take-up Reel-related errors do not occur on
Epson Stylus Pro
00M//7910/WT7900/WT/7908 because it
does not support the Auto Take-up Reel.
Errors related to the SpectroProofer and Auto
Take-up Reel do not occur on Epson Stylus Pro M.
D3&- Driving auto take-up
D6&- Driving paper pressing
65 - Cooling Fan lock detection error
12&- Paper Pressing Plate Sensor
no detection error
13&- Foreign material detection
error in paper pressing
14&- Paper pressing origin
position detection failure error
15&- CR HP Sensor no detection
16 - Paper pressing system abnormal measurement
value error
17&- Take-up system abnormal
measurement value error
20&- Slack Sensor no detection
01&- Mechanism is not installed
-(Mount Sensor is OFF)
30&- Driving time-out error
31&- Overload error
32&- Over speed error
33&- Reversing error
34&-&Velocity
deviation error
35&- Lock error
40- &Driving time-out error
41&- Overload error
42&- Over speed error
43&- Reversing error
44 - &Velocity deviation error
45&- Lock error
20 - Driving time-out error
Error Codes
Maintenance Requests Errors
MAINTENANCE REQ - 0040 - Cleaning unit is nearing
the end of life.
MAINTENANCE REQ - 0002 - Carriage motor is nearing the end of
MAINTENANCE REQ - 0008 - RTC backup battery is empty.
MAINTENANCE REQ - 0020 - The number of shots (per nozzle) reaches
the limit .
MAINTENANCE REQ - 0088 - The RTC backup battery is not
installed.
MAINTENANCE REQ - 0080 - Data is not specified.
MAINTENANCE REQ - 0100 - RTC backup battery is dropped
instantaneously.
Service Request Errors
SERVICE REQ -
- CR motor life
SERVICE REQ -
- PF motor encoder check error
SERVICE REQ -
- PF motor out of step
SERVICE REQ -
- PF motor overcurrent
SERVICE REQ -
- PF motor in-position time-out
SERVICE REQ -
- CR motor encoder check error
SERVICE REQ -
- CR motor out of step
SERVICE REQ -
- CR motor overcurrent
SERVICE REQ -
- CR motor in-position time-out
SERVICE REQ -
- Servo interrupt watchdog time-out
SERVICE REQ -
- System interrupt watchdog time-out
SERVICE REQ - 0001000A - CR home position sensor error
SERVICE REQ - 0001000B - PF home position sensor error
SERVICE REQ - 0001000C - Head slide (PG) home position sensor
SERVICE REQ - 0001000F - CR motor PWM output faulty
SERVICE REQ -
- PF motor PWM output faulty
SERVICE REQ - 0001001B - Head driver (TG) temperature error
SERVICE REQ - 0001001D - CR servo parameter error
SERVICE REQ - 0001001E - PF servo parameter error
SERVICE REQ -
- CSIC reed/right error
SERVICE REQ -
- Ink type error (setting on printer body
SERVICE REQ -
- RTC analysis error
SERVICE REQ -
- CSIC ROM communication error
SERVICE REQ -
- RTC communication error
SERVICE REQ -
- Head error
SERVICE REQ -
- Unidentified NMI
SERVICE REQ - 0001002A - CR ASIC ECU error
SERVICE REQ - 0001002B - PF ASIC ECU error
SERVICE REQ -
- NVRAM error
SERVICE REQ -
- SDRAM error
SERVICE REQ -
- BOOT program SUM error
SERVICE REQ -
- NVRAM error (3K)
SERVICE REQ -
- NVRAM error (32K)
SERVICE REQ -
- Flash memory SUM error
SERVICE REQ - 0002000A - Program load error
SERVICE REQ - 0002000B - Internal memory shortage error
SERVICE REQ - 0002000C - Review error
SERVICE REQ -
- CPU address error (load
misalignment)
SERVICE REQ -
- CPU address error (storage
misalignment)
SERVICE REQ -
- CPU reserve command code exception
SERVICE REQ -
- CPU slot illegal command exception
SERVICE REQ -
- CPU DMA address error
SERVICE REQ - 10000xxx - CPU error
Epson 7xx0 9xx0 Error Codes
Maintenance Requests Errors
MAINTENANCE REQ - 0002 - The number of carriage
movement cycles reached the specified value.
MAINTENANCE REQ - 0008 - The RTC backup battery run
down or is not installed.
MAINTENANCE REQ - 0040 - The pump counter reached
the specified upper limit.
MAINTENANCE REQ - 0080 - The date and time has not
MAINTENANCE REQ - 0100 - A momentary drop in
voltage of the RTC backup battery
MAINTENANCE REQ - 0400 - The Pressure Pump counter
reached the specified upper limit.
Service Request Errors
SERVICE REQ -
- The CR Motor reached its
end of life.
SERVICE REQ -
- PF Encoder check error
SERVICE REQ -
- The PF Motor is out of
SERVICE REQ -
- Overcurrent occurred on
the PF Motor.
SERVICE REQ -
- The PF Motor out of
position time-out error
SERVICE REQ -
- CR Encoder check error
SERVICE REQ -
- CR Motor is out of
SERVICE REQ -
- The CR Motor out of
position time-out error
SERVICE REQ -
- Servo interrupt watchdog
time-out error
SERVICE REQ -
- System interrupt watchdog
time-out error
SERVICE REQ - 0001000A - Carriage home position
detection error
SERVICE REQ - 0001000C - PG home position detection
SERVICE REQ -
- Failure of
pressurizing
SERVICE REQ - 0001001B - Head driver (TG)
temperature error
SERVICE REQ - 0001001D - CR servo parameter
SERVICE REQ - 0001001E - PF servo parameter
SERVICE REQ -
- CSIC reading/writing
SERVICE REQ -
- RTC analyzing error
SERVICE REQ -
- RTC communication
SERVICE REQ -
- Pressure pump micro
air-leak error
SERVICE REQ -
- Head error
SERVICE REQ - 0001002A - CR ASIC ECU error
SERVICE REQ - 0001002D - The Cleaning Unit reached
its end of life.
SERVICE REQ -
- Pump phase detection
SERVICE REQ -
- Type-B board installation
SERVICE REQ -
- Head thermistor error
SERVICE REQ -
- Transistor thermistor
SERVICE REQ - 0001003E - Pressure Sensor
SERVICE REQ - 0001003F - The Pressure Motor reached
its end of life.
SERVICE REQ -
- Printing position
SERVICE REQ -
- NVRAM error
SERVICE REQ -
- SDRAM error
SERVICE REQ -
- Boot program sum error
SERVICE REQ - 0002000A - Program load error
SERVICE REQ - 0002000B - The internal memory is
insufficient.
SERVICE REQ - 0Dxxxxxx - An error code for
SERVICE REQ - 0Exxxxxx - A time-lag of the RTC
SERVICE REQ -
- CPU address error
SERVICE REQ -
- CPU address error
SERVICE REQ -
- CPU reserved command code
exception error
SERVICE REQ -
- CPU slot undefined command
exception error
SERVICE REQ -
- The AC power is shut
SERVICE REQ -
- CPU DMA address error
SERVICE REQ - 10000xxx - CPU error
Epson 7xx0 9xx0 Error Codes
Maintenance Requests Errors
MAINTENANCE REQ - 0002 - The number of carriage
movement cycles reached the specified value.
MAINTENANCE REQ - 0008 - The RTC backup battery run
down or is not installed.
MAINTENANCE REQ - 0040 - The pump counter reached
the specified upper limit.
MAINTENANCE REQ - 0080 - The date and time has not
MAINTENANCE REQ - 0100 - A momentary drop in
voltage of the RTC backup battery
MAINTENANCE REQ - 0400 - The Pressure Pump counter
reached the specified upper limit.
Service Request Errors
SERVICE REQ -
- The CR Motor reached its
end of life.
SERVICE REQ -
- PF Encoder check error
SERVICE REQ -
- The PF Motor is out of
SERVICE REQ -
- Overcurrent occurred on
the PF Motor.
SERVICE REQ -
- The PF Motor out of
position time-out error
SERVICE REQ -
- CR Encoder check error
SERVICE REQ -
- CR Motor is out of
SERVICE REQ -
- The CR Motor out of
position time-out error
SERVICE REQ -
- Servo interrupt watchdog
time-out error
SERVICE REQ -
- System interrupt watchdog
time-out error
SERVICE REQ - 0001000A - Carriage home position
detection error
SERVICE REQ - 0001000C - PG home position detection
SERVICE REQ -
- Failure of
pressurizing
SERVICE REQ - 0001001B - Head driver (TG)
temperature error
SERVICE REQ - 0001001D - CR servo parameter
SERVICE REQ - 0001001E - PF servo parameter
SERVICE REQ -
- CSIC reading/writing
SERVICE REQ -
- RTC analyzing error
SERVICE REQ -
- RTC communication
SERVICE REQ -
- Pressure pump micro
air-leak error
SERVICE REQ -
- Head error
SERVICE REQ - 0001002A - CR ASIC ECU error
SERVICE REQ - 0001002D - The Cleaning Unit reached
its end of life.
SERVICE REQ -
- Pump phase detection
SERVICE REQ -
- Type-B board installation
SERVICE REQ -
- Head thermistor error
SERVICE REQ -
- Transistor thermistor
SERVICE REQ - 0001003E - Pressure Sensor
SERVICE REQ - 0001003F - The Pressure Motor reached
its end of life.
SERVICE REQ -
- Printing position
SERVICE REQ -
- NVRAM error
SERVICE REQ -
- SDRAM error
SERVICE REQ -
- Boot program sum error
SERVICE REQ - 0002000A - Program load error
SERVICE REQ - 0002000B - The internal memory is
insufficient.
SERVICE REQ - 0Dxxxxxx - An error code for
SERVICE REQ - 0Exxxxxx - A time-lag of the RTC
SERVICE REQ -
- CPU address error
SERVICE REQ -
- CPU address error
SERVICE REQ -
- CPU reserved command code
exception error
SERVICE REQ -
- CPU slot undefined command
exception error
SERVICE REQ -
- The AC power is shut
SERVICE REQ -
- CPU DMA address error
SERVICE REQ - 10000xxx - CPU error
Error Codes
Maintenance Request Errors
MAINTENANCE REQ - 0002 - The CR scan pass counter
has come near the specified life.
MAINTENANCE REQ - 0008 - The RTC backup battery
becomes exhausted
MAINTENANCE REQ - 0010 - Communication with the AID
Board is not established.
MAINTENANCE REQ - 0040 - The pump counter has come
near the specified life.
MAINTENANCE REQ - 0080 - The date has not been
MAINTENANCE REQ - 0800 - Cartridge holder diaphragm
near end of life
MAINTENANCE REQ - 1000 - Ink Selector near end of
MAINTENANCE REQ - 4000 - It detects twice in a row
that all the nozzles are clogging.
MAINTENANCE REQ - 0088 - The RTC backup battery
becomes exhausted and the date has not been set.
Service Request Errors
SERVICE REQ - 1101 - CR life error
SERVICE REQ - 1125 - CR HP detection error
SERVICE REQ - 1138 - Over current error
SERVICE REQ - 113A - Overload error
SERVICE REQ - 113B - Over speed error
SERVICE REQ - 113C - Reversing error
SERVICE REQ - 113D - Driving time-out error
SERVICE REQ - 113E - Velocity deviation error
SERVICE REQ - 113F - Lock error
SERVICE REQ - 122A - Overload error
SERVICE REQ - 122B - Over speed error
SERVICE REQ - 122C - Reversing error
SERVICE REQ - 122D - Driving time-out error
SERVICE REQ - 122E - Velocity deviation error
SERVICE REQ - 122F - Lock error
SERVICE REQ - 131B - Head driver (transmission
gate) overheat error
SERVICE REQ - 1412 - Motor Life Error
SERVICE REQ - 141A - Overload error
SERVICE REQ - 141B - Over speed error
SERVICE REQ - 141C - Reversing error
SERVICE REQ - 141D - Driving time-out error
SERVICE REQ - 141E - Velocity deviation error
SERVICE REQ - 141F - Lock error
SERVICE REQ - 1431 - Ink selector life error
SERVICE REQ - 1432 - IC Holder life error
SERVICE REQ - 1433 - IS Unit position sensor
SERVICE REQ - 1494 - Ink selector error
SERVICE REQ - 1496 - Ink selector sensor error
SERVICE REQ - 1497 - Switching time-out error
SERVICE REQ - 149D - Driving time-out error
SERVICE REQ - 150C - PG phase detection error
SERVICE REQ - 151A - Overload error
SERVICE REQ - 151B - Over speed error
SERVICE REQ - 151C - Reversing error
SERVICE REQ - 151D - Driving time-out error
SERVICE REQ - 151E - Velocity deviation error
SERVICE REQ - 151F - Lock error
SERVICE REQ - 1520 - Roll feed motor lock retry
SERVICE REQ - 1521 - Roll feed sensor detect
SERVICE REQ - 1523 - Roll sensor error
SERVICE REQ - 151A - Overload error
SERVICE REQ - 151B - Over speed error
SERVICE REQ - 151C - Reversing error
SERVICE REQ - 152D - Driving time-out error
SERVICE REQ - 152E - Velocity deviation error
SERVICE REQ - 152F - Lock error
SERVICE REQ - 1530 - HP detection error
SERVICE REQ - 1531 - Release Sensor error
SERVICE REQ - 153A - Overload error
SERVICE REQ - 153B - Over speed error
SERVICE REQ - 153C - Reversing error
SERVICE REQ - 153D - Driving time-out error
SERVICE REQ - 153E - Velocity deviation error
SERVICE REQ - 153F - Lock error
SERVICE REQ - 1540 - Cutter HP detection error
SERVICE REQ - 1541 - Cutter return error
SERVICE REQ - 1549 - Motor disconnection error
SERVICE REQ - 154A - Overload error
SERVICE REQ - 154B - Cutter Motor over speed
SERVICE REQ - 154C - Cutter Motor reversing
SERVICE REQ - 154D - Driving time-out error
SERVICE REQ - 154E - Velocity deviation error
SERVICE REQ - 154F - Lock error
SERVICE REQ - 1551 - Paper thickness determining
SERVICE REQ - 155A - DCP Motor overload error
SERVICE REQ - 155B - DCP Motor over speed error
SERVICE REQ - 155C - DCP Motor reversing error
SERVICE REQ - 155D - DCP Motor driving time-out
SERVICE REQ - 155E - DCP Motor velocity deviation
SERVICE REQ - 155F - DCP Motor lock error
SERVICE REQ - 1561 - Paper thickness at power-on
SERVICE REQ - 1562 - ASF Motor abnormal load
detection error
SERVICE REQ - 156A - ASF Motor overload error
SERVICE REQ - 156B - ASF Motor over speed error
SERVICE REQ - 156C - ASF Motor reversing error
SERVICE REQ - 156D - ASF Motor driving time-out
SERVICE REQ - 156E - ASF Motor velocity deviation
SERVICE REQ - 156F - ASF Motor lock error
SERVICE REQ - 1571 - ASF Retard Roller Sensor
operation error
SERVICE REQ - 1572 - ASF Pickup Roller operation
SERVICE REQ - 1573 - ASF Assist Roller operation
SERVICE REQ - 157A - ASF Sub Motor overload
SERVICE REQ - 157B - ASF Sub Motor over speed
SERVICE REQ - 157C - ASF Sub Motor reversing
SERVICE REQ - 157D - ASF Sub Motor driving time-out
SERVICE REQ - 157E - ASF Sub Motor velocity
deviation error
SERVICE REQ - 157F - ASF Sub Motor lock error
SERVICE REQ - 1581 - Paper eject position error
SERVICE REQ - 1582 - ASF Edge Guide open/close
SERVICE REQ - 158A - EG Motor overload error
SERVICE REQ - 158B - EG Motor over speed error
SERVICE REQ - 158C - EG Motor reversing error
SERVICE REQ - 158D - EG Motor driving time-out
SERVICE REQ - 158E - EG Motor velocity deviation
SERVICE REQ - 158F - EG Motor lock error
SERVICE REQ - 159A - ATC Motor overload error
SERVICE REQ - 159B - ATC Motor over speed error
SERVICE REQ - 159C - ATC Motor reversing error
SERVICE REQ - 159D - ATC Motor driving time-out
SERVICE REQ - 159E - ATC Motor velocity deviation
SERVICE REQ - 159F - ATC Motor lock error
SERVICE REQ - 1801 - AID voltage error
SERVICE REQ - 1A23 - Incorrect RTC data error
SERVICE REQ - 1A26 - RTC Access T/O error
SERVICE REQ - 1A37 - Thermistor error
SERVICE REQ - 1A38 - Transistor environmental
temperature error
SERVICE REQ - 1A39 - Head error
SERVICE REQ - 1A41 - Head rank ID input error
SERVICE REQ - 1A50 - I2C communication error
(Between elements on ASIC and MAIN)
SERVICE REQ - 1A51 - I2C communication error
(Between elements on SUB and MAIN)
SERVICE REQ - 1ABx - Main Board communication
SERVICE REQ - 1Fxx - ILS error (1)
SERVICE REQ - 2000 - NVRAM error
SERVICE REQ - 2002 - SDRAM error
SERVICE REQ - 2003 - FLASH BOOT SUM CHECK error
SERVICE REQ - 200A - F/W load error
SERVICE REQ - 200D - System interrupt watchdog
time-out error
SpectroProofer Errors
01 - SpectroProofer uninstallation error
02 - Paper Eject Support uninstallation error
13 - Foreign material detection error in paper
14 - Paper pressing origin position detection
failure error
15 - CR HP Sensor no detection error
16 - Paper pressing system abnormal measurement
value error
65 - Drying Fan lock detection error
80 - ILS calibration error
D5 - CR related drive error
D6 - Paper pressing related operating error
Epson 4xx0 Error Codes
Maintenance Requests Errors
MAINTENANCE REQ - 0002 - The number of CR movement
cycles has reached predetermined value
MAINTENANCE REQ - 0008 - RTC backup battery shut
MAINTENANCE REQ - 0040 - Pump counter has reached
predetermined amount.
MAINTENANCE REQ - 0080 - Date is not set
MAINTENANCE REQ - 0088 - RTC backup battery is not
installed.
MAINTENANCE REQ - 0100 - RTC backup battery
pressure is temporally low.
MAINTENANCE REQ - 0200 - The number of ASF paper
feeding has reached predetermined value.
Service Request Errors
SERVICE REQ -
- CR Motor life
SERVICE REQ -
- PF Motor Encoder check
SERVICE REQ -
- PF Motor out of step
SERVICE REQ -
- PF Motor over current
SERVICE REQ -
- PF Motor in-position
SERVICE REQ -
- CR Motor Encoder check
SERVICE REQ -
- CR Motor out of step
SERVICE REQ -
- CR Motor over current
SERVICE REQ -
- CR Motor in-position
SERVICE REQ -
- Servo interrupt watchdog
SERVICE REQ -
- System interrupt watchdog
SERVICE REQ - 0001000A - CR axis detection
SERVICE REQ - 0001000C - PG axis detection
SERVICE REQ - 0001000F - CR Motor PWM output
SERVICE REQ -
- PF Motor PWM output
SERVICE REQ -
- CR overload (high
sensitivity) error
SERVICE REQ -
- PR overload (high
sensitivity) error
SERVICE REQ - 0001001B - Head driver (TG)
temperature error
SERVICE REQ - 0001001D - CR servo parameter
SERVICE REQ - 0001001E - PF servo parameter
SERVICE REQ -
- CSIC reed/right error
SERVICE REQ -
- Ink type error (setting on
printer body side)
SERVICE REQ -
- RTC analysis error
SERVICE REQ -
- CSIC ROM communication
SERVICE REQ -
- RTC communication
SERVICE REQ -
- Head error
SERVICE REQ -
- Unidentified NMI
SERVICE REQ - 0001002A - CR ASIC ECU error
SERVICE REQ - 0001002B - PF ASIC ECU error
SERVICE REQ - 0001002D - Cleaning Unit work life
SERVICE REQ - 0001002F - 360 DPI writing time out
SERVICE REQ -
- Multi Sensor failure
SERVICE REQ -
- ASF phase detection
SERVICE REQ -
- ASF drive switch error
SERVICE REQ -
- Eject phase detection
SERVICE REQ -
- Eject movement error
SERVICE REQ -
- Pump phase detection
SERVICE REQ -
- Type-B board installation
SERVICE REQ -
- Head thermistor error
SERVICE REQ -
- Transistor thermistor
SERVICE REQ -
- PG adjustment value
incorrect overwrite error
SERVICE REQ - 0001003A - PG adjustment value
outside range error
SERVICE REQ - 0001003B - Cutter installation error
SERVICE REQ - 0001003C - Cutter installation error
SERVICE REQ - 0001003D - Cutter installation error
SERVICE REQ -
- NVRAM error
SERVICE REQ -
- SDRAM error
SERVICE REQ -
- BOOT program SUM error
SERVICE REQ -
- Flash memory SUM error
SERVICE REQ - 0002000A - Program load error
SERVICE REQ - 0002000B - Internal memory shortage
SERVICE REQ -
- CPU address error (load
misalignment)
SERVICE REQ -
- CPU address error (storage
misalignment)
SERVICE REQ -
- CPU reserve command code
exception error
SERVICE REQ -
- CPU slot illegal command
exception error
SERVICE REQ -
- AC disruption
SERVICE REQ -
- CPU DMA address error
SERVICE REQ - 10000xxx - CPU error
SERVICE REQ - 0003xxxx - Debug error code
SERVICE REQ - 0Dxxxxxx - Debug error code
SERVICE REQ - 0Exxxxxx - RTC timer off error
Epson 4000 Error Codes
Maintenance Requests Errors
MAINTENANCE REQ - 0002 - The number of CR movement
cycles has reached predetermined value
MAINTENANCE REQ - 0008 - RTC backup battery shut
MAINTENANCE REQ - 0040 - Pump counter has reached
predetermined amount.
MAINTENANCE REQ - 0080 - Date is not set
MAINTENANCE REQ - 0088 - RTC backup battery is not
installed.
MAINTENANCE REQ - 0100 - RTC backup battery
pressure is temporally low.
MAINTENANCE REQ - 0200 - The number of ASF paper
feeding has reached predetermined value.
Service Request Errors
SERVICE REQ -
- CR Motor life
SERVICE REQ -
- PF Motor Encoder check
SERVICE REQ -
- PF Motor out of step
SERVICE REQ -
- PF Motor over current
SERVICE REQ -
- PF Motor in-position
SERVICE REQ -
- CR Motor Encoder check
SERVICE REQ -
- CR Motor out of step
SERVICE REQ -
- CR Motor over current
SERVICE REQ -
- CR Motor in-position
SERVICE REQ -
- Servo interrupt watchdog
SERVICE REQ -
- System interrupt watchdog
SERVICE REQ - 0001000A - CR axis detection
SERVICE REQ - 0001000C - PG axis detection
SERVICE REQ - 0001000F - CR Motor PWM output
SERVICE REQ -
- PF Motor PWM output
SERVICE REQ - 0001001B - Head driver (TG)
temperature error
SERVICE REQ - 0001001D - CR servo parameter
SERVICE REQ - 0001001E - PF servo parameter
SERVICE REQ -
- CSIC reed/right error
SERVICE REQ -
- Ink type error (setting on
printer body side)
SERVICE REQ -
- RTC analysis error
SERVICE REQ -
- CSIC ROM communication
SERVICE REQ -
- RTC communication
SERVICE REQ -
- Head error
SERVICE REQ -
- Unidentified NMI
SERVICE REQ - A - CR ASIC ECU error
SERVICE REQ - 0001002B - PF ASIC ECU error
SERVICE REQ - 0001002D - Cleaning Unit work life
SERVICE REQ - 0001002F - 360 DPI writing time out
SERVICE REQ -
- Multi Sensor failure
SERVICE REQ -
- ASF phase detection
SERVICE REQ -
- ASF drive switch error
SERVICE REQ -
- Eject phase detection
SERVICE REQ -
- Eject movement error
SERVICE REQ -
- Pump phase detection
SERVICE REQ -
- Type-B board installation
SERVICE REQ -
- Head thermistor error
SERVICE REQ -
- Transistor thermistor
SERVICE REQ -
- PG adjustment value
incorrect overwrite error
SERVICE REQ - 0001003A - PG adjustment value
outside range error
SERVICE REQ - 0001003B - Cutter installation error
SERVICE REQ - 0001003C - Cutter installation error
SERVICE REQ - 0001003D - Cutter installation error
SERVICE REQ -
- NVRAM error
SERVICE REQ -
- SDRAM error
SERVICE REQ -
- BOOT program SUM error
SERVICE REQ -
- Flash memory SUM error
SERVICE REQ - 0002000A - Program load error
SERVICE REQ - 0002000B - Internal memory shortage
SERVICE REQ -
- CPU address error (load
misalignment)
SERVICE REQ -
- CPU address error (storage
misalignment)
SERVICE REQ -
- CPU reserve command code
exception error
SERVICE REQ -
- CPU slot illegal command
exception error
SERVICE REQ -
- AC disruption
SERVICE REQ -
- CPU DMA address error
SERVICE REQ - 10000xxx - CPU error
SERVICE REQ - 0003xxxx - Debug error code
SERVICE REQ - 0Dxxxxxx - Debug error code
Error Codes
Maintenance Requests Errors
MAINTENANCE REQ - 0100 - Indicates small quantity
of remaining waste ink material absorption.
MAINTENANCE REQ - 0101 - The CR motor reached the 3% remaining to
MAINTENANCE REQ - 0102 - Auto nozzle check
MAINTENANCE REQ - 0103 - Backup battery for RTC
(real time clock) life expired.
MAINTENANCE REQ - 0104 - Dot missing detector
Service Request Errors
SERVICE REQ -
- Waste ink pads are
SERVICE REQ -
- CR motor life (Ink tubes
also reached their life)
SERVICE REQ -
- Nozzle check error
compulsory continuity
SERVICE REQ -
- RTC backup battery end
SERVICE REQ -
- Auto print head
optimization system
SERVICE REQ -
- Head unit life end
SERVICE REQ -
- Cleaning unit life end
SERVICE REQ -
- PF motor/ encoder check
SERVICE REQ -
- PF motor step-out
SERVICE REQ -
- PF motor/overcurrent
SERVICE REQ -
- PF motor/ in position
time-out error
SERVICE REQ -
- CR motor/ encoder check
SERVICE REQ -
- CR motor step-out
SERVICE REQ -
- CR motor/overcurrent
SERVICE REQ -
- CR motor/ in position
time-out error
SERVICE REQ -
- Servo interruption watch
dog time out error
SERVICE REQ -
- System interruption watch
dog time out error
SERVICE REQ - 0001000A - CR origin sensor
mulfanction
SERVICE REQ - 0001000B - PF origin sensor
mulfanction
SERVICE REQ - 0001000C - HS origin sensor
mulfanction
SERVICE REQ - 0001000D - Cover sensor
mulfanction
SERVICE REQ - 0001000E - Cover sensor
mulfanction
SERVICE REQ - 0001000F - CR motor over heat (PWM
output malfunction)
SERVICE REQ -
- PF motor over heat (PWM
output malfunction)
SERVICE REQ -
- Paper jam error
SERVICE REQ -
- Cap origin error
SERVICE REQ -
- Providing system origin
SERVICE REQ -
- Pressurization error
SERVICE REQ -
- Liquid sensor overflow
SERVICE REQ -
- Liquid sensor
overflow(C)
SERVICE REQ -
- Liquid sensor overflow
SERVICE REQ -
- Liquid sensor overflow
SERVICE REQ -
- Liquid sensor overflow
SERVICE REQ - 0001001A - Liquid sensor overflow
SERVICE REQ - 0001001B - Head driver (TG)
temperature error
SERVICE REQ - 0001001C - FS origin (Suction fan
shutter home position) error
SERVICE REQ - 0001001D - CR servo parameter
SERVICE REQ - 0001001E - PF servo parameter
SERVICE REQ -
- CSIC card read/write
SERVICE REQ -
- Starter cartridge
SERVICE REQ -
I- nk type NVRAM status
SERVICE REQ -
- RTC operation
malfunction
SERVICE REQ -
- Module communication
time-out error
SERVICE REQ -
- CSIC EEROR access
SERVICE REQ -
- RTC access error
SERVICE REQ -
- Pressure pump small leak
SERVICE REQ -
- During cleaning, pressure
pump small leak error
SERVICE REQ -
- NVRAM error
SERVICE REQ -
- NVRAM check sum error
SERVICE REQ -
- SDRAM error
SERVICE REQ -
- Flash memory sum error
SERVICE REQ -
- ASIC illegal version
SERVICE REQ -
- Firmware ASIC mismatching
error (Version:A)
SERVICE REQ -
- Firmware ASIC mismatching
error (Version:B)
SERVICE REQ -
- Head/ASIC mismatch
SERVICE REQ -
- Flash memory check sum
SERVICE REQ - 0002000B - Memory insufficient
SERVICE REQ - 0002000C - Review error
SERVICE REQ -
- Debug error
SERVICE REQ -
- Ink supply defective
SERVICE REQ -
- Ink supply defective
SERVICE REQ -
- Ink supply defective
SERVICE REQ -
- Ink supply defective
SERVICE REQ -
- Ink supply defective
SERVICE REQ - 0003001A - Ink supply defective
SERVICE REQ - 0003001B - GAP adjustment range
SERVICE REQ - 0003001C - Timeout in case of no
print finishing with ASIC
SERVICE REQ - D0120013 - Module comminication
SERVICE REQ - D012001E - Engine side ASIC command
transmission over flow
SERVICE REQ - D012001F - Engine side ASIC command
receiption over error
SERVICE REQ - D0xxxxxx - Program error
SERVICE REQ - 10000E0 - CPU address error
SERVICE REQ - 1000100 - CPU address error
SERVICE REQ -
- CPU reservation
instruction code exception error
SERVICE REQ -
- CPU Slot unfair command
exception error
SERVICE REQ -
- CPU DMA address error
SERVICE REQ - 10000xxx - CPU illegal trap
SERVICE REQ - FFFFxxxx - OS kernel detection
已投稿到：
以上网友发言只代表其个人观点，不代表新浪网的观点或立场。