Hurtownia Materia?ów Telekomunikacyjnych i Energetycznych
Gwarantujemy pe?ny asortyment materia?ów i towarów do budowy sieci telekomunikacyjnych oraz – cz??ciowo – sieci elektroenergetycznych. Wszystkie posiadane przez nas materia?y i towary s? produkcji polskiej i posiadaj? wymagane certyfikaty, deklaracje zgodno?ci oraz gwarancje wynikaj?ce z obowi?zuj?cych norm i przepisów w tym zakresie.
Zapraszamy do wspó?pracy
TP TELE-TELTECH sp. z o.o.
ul. Ks. Klimasa 8, 50-515 Wroc?aw
tel. +48 71 336 72 42, +48 71 336 01 31华为hg255d，从电信原版到dreambox-openwrt免拆机详细刷机教程 - OPENWRT专版 - 恩山无线论坛 - Powered by Discuz!
后使用快捷导航没有帐号？
只需一步，快速开始
请完成以下验证码
请完成以下验证码
查看: 112454|回复: 180
华为hg255d，从电信原版到dreambox-openwrt免拆机详细刷机教程
本帖最后由 北宫一 于
20:33 编辑
按照lintel提供的教程，本人新搞的hg255d刷机一次搞定。特总结一下自己的刷机经验，并将一些小细节补充上。
注意：刷完u-boot之后，不能刷电信原版的固件,要想刷原版固件需要把u-boot换回电信原版的。
& && && & 刷 固件不能在openwrt界面内进行，只能tftp更新固件。
& && && & 感谢8楼非云的补充
& &hg255d不算是新路由了，秉承电信定制机器的一贯作风，此机走上了开源的道路，也如lintel所说，此机的u-boot很个性。所以想玩此机的朋友最好是更新u-boot。此教程是在更新u-boot的前提下完成的（其实我也不想更新，但是shcl的0508固件刷不进去，索性就不搞了直接更换u-boot）
下面是我的路由器的一些基本信息
很神奇的是固件里显示的硬件版本是A，而实际的拆机看是D，不过不影响刷机。
451b1d4f.jpg (53.08 KB, 下载次数: 67)
17:37 上传
QQ截图52.jpg (64.04 KB, 下载次数: 34)
17:37 上传
二.流程概要：
&&电信原版-》ralink固件-》替换u-boot-》tftp openwrt-》end
三.详细流程
&&1.设置本地连接为 192.168.1.100 mask 255.255.255.0 网关 192.168.1.1，DNS不用填写（以后只要更新固件就是192.168.1.100的固定ip切记切记），网线与hg255d连接好，保持机器关闭状态
QQ截图28.jpg (42.85 KB, 下载次数: 44)
17:40 上传
2.先在浏览器输入 ，然后按住路由的reset键并接通电源，保持reset按住，浏览器刷新刚才的那个地址，大约十秒左右就可以进入如图所示的界面，此时一定要抓紧选择ralink.bin（此固件内已包含改版u-boot和电信原版u-boot，后面u-boot-rom-hg255d_hg256.bin是升级用的）固件并开始刷入，因为在10-20秒以后，路由将正常启动，页面输入固件将会失败。切记速度！！！lan口灯狂闪，ralink固件写入结束，大约5min之后路由会自动重启，稍等片刻在浏览器中输入192.168.1.1
帐号密码同为admin.进入ralink的设置界面
do2pdzmapar_jpg_thumb.jpg (39.37 KB, 下载次数: 47)
17:50 上传
3.刷u-boot很简单，只需要执行一个shell就可以了.找到 系统管理-&系统指令。
执行命令：/hg255d/hg255d-flash-uboot.sh& &提交一下
大约1-2秒就结束了，很快的，然后手动重启路由器。（如想恢复电信原固件，用tftp重刷ralink.bin固件，执行/hg255d/hg255d-flash-tel-uboot.sh就OK了）
untitled.png (230.39 KB, 下载次数: 49)
19:00 上传
4.路由重启后，只要是电源灯频闪基本上就说明刷u-boot成功了，这里要说明一下，其实开机的时候不用按 wps/wlan/reset按钮.，也能进行tftp，不过要是你动作慢了，路由会自动启动成功的，tftp就不起作用了，保险起见，还是开机的时候按住wps/wlan/reset按钮任一按钮，然后刷入固件就行了，写入固件0831-DreamBox-ramips-rt305x-hg255d-squashfs-sysupgrade.bin大约10秒钟，此时电源灯为常亮，然后大约是5分钟的等待时间，电源灯会灭一下，然后频闪，之后稍等一会就可以192.168.1.1进入DreamBox
QQ截图03.jpg (25.38 KB, 下载次数: 40)
19:11 上传
至此刷机结束。
--------------------------------------------------------------------------------------------------------------------------------
此步骤是升级u-boot，可以不进行，lintel的最新u-boot已经支持大内存了，索性我也升级了一下
还是按住wps/wlan/reset任一键，开机，电源灯频闪，然后tftp提交u-boot-rom-hg255d_hg256.bin，5分钟之后，路由自动重启就成功了
QQ截图39.jpg (22.44 KB, 下载次数: 39)
19:17 上传
全部用到的工具及固件
成功刷入,那个李寻欢就是个SB,sh文件是shell脚本文件,不懂就别BB....&
楼主那个SHELL命令，误导了多少人啊。这个命令文件名也不对，路径也不对。你的网盘文件是BIN，命令是sh文件。&
太给力了。。。百试不爽&
强大的恩山！(以下重复1万次)
教程很给力。支持
白富美露出了诧异的眼神：屌丝，你真是太厉害了！对于我这个菜鸟来说，这个贴对我的帮
执行命令：/hg255d/hg255d-flash-uboot.sh 我等了不
终于告别0508了。顺利刷成0828.谢谢楼主！
泥马，真给力，我要顶! 成功了
泥马，真给力，我要顶!
赞一个，你是我的呕像!
赞一个，你是我的呕像!
我的恩山、我的无线
The best wifi forum is right here.
楼主，非常感谢您写的这个教程，身为一个小白，按照论坛流行的WEB刷 怎么都不成功。
在犹豫是否要买JTAG 跳线刷机时，按照这个教程 一次成功 真的是很给力。。。
我的恩山、我的无线
The best wifi forum is right here.
我的恩山、我的无线
The best wifi forum is right here.
我的恩山、我的无线
The best wifi forum is right here.
不错，标记一下
我的恩山、我的无线
The best wifi forum is right here.
楼主，你刷了之后无线的mac有吗，据说有个eeprom要备份，不然没有无线mac
不知道是不是这样
我的恩山、我的无线
The best wifi forum is right here.
顶上详细教程！
我的恩山、我的无线
The best wifi forum is right here.
楼主思路清晰，我已经成功把半砖机救回！不过有几个细节要修改一下！免得新手百思不解！
(30.2 KB, 下载次数: 119)
10:32 上传
用tftp要改电脑的IP
我的恩山、我的无线
The best wifi forum is right here.
我刷机用超级终端监控
(72.47 KB, 下载次数: 93)
10:35 上传
我的恩山、我的无线
The best wifi forum is right here.
最终的界面
(78.61 KB, 下载次数: 79)
10:36 上传
我的恩山、我的无线
The best wifi forum is right here.
tftp要记得打勾
(43.59 KB, 下载次数: 94)
10:38 上传
我的恩山、我的无线
The best wifi forum is right here.
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
fuse init (API version 7.13)
device wlan0 entered promiscuous mode
br-lan: port 5(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 5(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 5(wlan0) entering forwarding state
ramips-wdt: timeout value 60 must be 0 & timeout & 33
br-lan: port 5(wlan0) entering disabled state
br-lan: port 5(wlan0) entering forwarding state
我的恩山、我的无线
The best wifi forum is right here.
记事本太长了传不上来
我的恩山、我的无线
The best wifi forum is right here.
fuse init (API version 7.13)
device wlan0 entered promiscuous mode
br-lan: port 5(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 5(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 5(wlan0) entering forwarding state
ramips-wdt: timeout value 60 must be 0 & timeout & 33
br-lan: port 5(wlan0) entering disabled state
br-lan: port 5(wlan0) entering forwarding state& &最终的结果
我的恩山、我的无线
The best wifi forum is right here.
感谢楼主，不错的帖子
我的恩山、我的无线
The best wifi forum is right here.
Powered by·17-08-21&
·17-08-07&
·17-08-04&
·17-08-02&
·17-08-01&
·17-07-19&
·17-07-18&
·17-07-14&
·17-07-07&
·17-07-06&
‖& 友情链接
杭州汽轮动力集团有限公司
杭州南方通达齿轮有限公司
杭州中能汽轮动力有限公司
杭州汽轮辅机有限公司
浙江透平进出口贸易有限公司
杭州汽轮机械设备有限公司
杭州汽轮铸锻有限公司
‖& 更多链接
安全防范宣传
版权所有：杭州汽轮机股份有限公司&地址：浙江省杭州市石桥路357号&总机：+86-571-TP-LINK TL-WR703N Configuration & Hack
TP-LINK TL-WR703N Configuration & Hack
& & &&TP-LINK TL-WR703N is a very low cost customisable Wifi, Ethernet and 3G enabled miniature router.
Not only can it be a ethernet router, it can be modify as a controller to control other hardware or for robotic control.
It is a mini Linux computer by itself, which is able to perform a lot of electronics tasks.
Edited by Lim Siong Boon, last dated 06-Oct-2013.
Discussion Overview
Introduction
You can flash other open source firmware like open-wrt onto this
router. The illustration above provide a guide to select your new
firmware to flash onto the router device (Chinese menu).
New firmware flashing in progress.
Wireless N Router TL-WR703N, Chinese version
Default gateway address: 192.168.1.1
Default username: admin
Default password: admin
Webserver for TL-MR3020, flash onto the TP-WR703N hardware.
3G Wireless N Router TL-MR3020, English version
- Datasheet
Default gateway address: 192.168.0.254
Default username: admin
Default password: admin
3G/4G USB Modem Compatibility List
EE E153 EG E173 E E180 E MF626 3531
X060S X070S X080S X200S X215S X225S X310E BL-EV08C BL-HD72A U1 U1-TF
DWM-151 DWM-152 DWM-156 DWM-162 DWM-652 E122 E E
E156B E156C E160 E160E E160G E160X E EG E
E173s-2 ECu E1752c E E E E2010
E220 E226 E230 E270 E272 E352 E367 E372 E870 EC121 EC122 EC1260 EC1261
EC1261-2 EC1262 EC150 EC152 EC168C EC169 K K K3770
K4505 TestModelNo X225S CS-10 CS-12 CS-15 CS-17 PX500 PHS100 SGH-H128
MA180 MA260 (webConnect Rocket) USB STICK 120 AC2726 AC2726i AC2736
AC2746 AC2766 AC581 AC682 AC8700 AC-Z K3570-Z K3765-Z K3805-Z
K3806-Z K4505-Z MF100 MF102 MF110 MF112 MF160 MF161 MF163 MF170 MF180
MF190 MF192 MF622 MF626i MF627 MF631 MF633 MF636 MF637 MF637U MF645
MF668 MF668+ MF688 MU351
Flashing TL-WR703N Wireless Router ()
1) Connect up TL-WR703N Wireless Router
2) Go to webserver 192.168.1.1, User/Password: admin/admin
3) Click 系统工具&软件升级 to flash firmware witn openWrt firmware.
4) Win7, go to Programs and Features to enable the Telnet Client in Win7
5) Type "Telnet" in the search bar to search for Telnet program in Win7
6) In the telnet program type "open 192.168.1.1" to connect to the router.
or use PuTTY to access
7) Need to set password for GUI web interface
type passwd, new password as "admin". type in again to confirm.
8) Relogin using SSH (will not be able to telnet once password is set)
- login as: root
- password: admin
9) Use VI to edit the central network configuration located in /etc/config/network.
- vi /etc/config/network
- change IP from 192.168.1.1 to 192.168.1.40
- add in the "option gateway '192.168.1.1'" to allow the device to locate for the gateway for internet access.
- add in the option dns '192.168.1.254' to allow router to resolved web address name. DNS taken from home router.
10) Either reboot the device or run "/etc/init.d/network restart" to apply the settings.
11) Run "opkg update" and "opkg install luci" to install the web interface.
12) You will have to enable and start uhttpd daemon afterwards:
/etc/init.d/uhttpd enable
/etc/init.d/uhttpd start
13) Key in the device TL-WR703N IP address into the web browser. The web server page should load.
---------------------------------------------------------
12) /etc/config/wireless
config wifi-device
option type
option channel
option macaddr
38:83:45:d3:10:4c
option hwmode
option htmode
list ht_capab
SHORT-GI-20
list ht_capab
SHORT-GI-40
list ht_capab
list ht_capab
DSSS_CCK-40
# REMOVE THIS LINE TO ENABLE WIFI:
option disabled 1
config wifi-iface
option device
option network
option mode
option ssid
option encryption none
13) /etc/config/network
config 'interface' 'loopback'
option 'ifname' 'lo'
option 'proto' 'static'
option 'ipaddr' '127.0.0.1'
option 'netmask' '255.0.0.0'
config 'interface' 'lan'
option 'ifname' 'eth0'
option 'type' 'bridge'
option 'proto' 'static'
option 'ipaddr' '192.168.0.51'
option 'netmask' '255.255.255.0'
option 'dns' '8.8.8.8'
option 'gateway' '192.168.1.1'
config 'interface' 'wireless'
option 'ifname' 'radio0'
option 'proto' 'dhcp'
option 'proto' 'static'
option 'ipaddr' '192.168.1.51'
option 'netmask' '255.255.255.0'
option 'dns' '8.8.8.8'
option 'gateway' '192.168.1.1'
for TP-WR703N
TL-WR703N Firmware Recovery
Schematic:
Information taken from another website.
TL-WR703N allows user to flash various open source router's firmware.
You can do all sorts of settings you like, but what if you did it
wrongly and is no longer able to reach back to your router to do
configuration. The last resort which is the most troublesome procedure
is to access the device through the serial. For this, you will need to
open open the device.
Opening up the device you will be the PCB circuit board. You will need to solder 3 signal wire out for serial access. They are,
will need to solder these 3 point out onto a header, so that we can
connect a USB TTL converter, to access the console through the serial
Click picture to enlarge. The 3 pad is to be solder for the access to the device serial console.
The following pictures show what I did,
Preparing USB comm device for access into the TL-WR703N router's console.
The following is the pins connection from the USB comm device to the router's console.
USB comm device
TP-WR703N pin out
After the comm device is connected to the TL-WR703N circuit PCB, connect this USB comm device to your computer.
A vitual serial
comm port will be created in the Device Manager.
From WindowsOS, you can go to Start-& Control Panel-& Device Manager.
Take note of the com port number. For this example, the USB comm device is COM6.
Open a serial communication terminal program like
or , to access the serial. Serial settings should be as follows,
- Buadrate 115200bps
- 8 data bits
- 1 stop bit
- no parity
- no hardward control
The following is the docklight script with command listed for operation in command execution steps later.
Connect to COM6 with your terminal program.
Download and install the following TFTP server to your computer.
Setup the IP address of the computer to 192.168.1.100.
Connect the Ethernet cable from your computer to the Ethernet port of the TP-WR703N.
Ensure that the firewall is off, or permission is granted for the server's TFTP communication.
the *.bin firmware that you want to load into the TP-WR703N router onto
your computer's directory. In this example, copy the
"wr703nv1_cn_3_12_11_up(110926).bin" onto D:\
On the TFTP
program, setup the Current Directory to the directory containing your
*.bin file. The Server Interface should be 192.168.1.100.
The server will starts to accept incoming connection once the program is launched.
U-Boot 1.1.4 (Feb 28 2012 - 11:58:24)&CR&&LF&
AP121 (ar9330) U-boot&CR&&LF&
32 MB&CR&&LF&
led turning on for 1s...&CR&&LF&
id read 0x100000ff&CR&&LF&
flash size 4194304, sector count = 64&CR&&LF&
4 MB&CR&&LF&
Using default environment&CR&&LF&
serial&CR&&LF&
serial&CR&&LF&
serial&CR&&LF&
ag7240_enet_initialize...&CR&&LF&
No valid address in Flash. Using fixed address&CR&&LF&
No valid address in Flash. Using fixed address&CR&&LF&
: cfg1 0x5 cfg2 0x7114&CR&&LF&
eth0: 00:03:7f:09:0b:ad&CR&&LF&
ag7240_phy_setup &CR&&LF&
eth0 up&CR&&LF&
: cfg1 0xf cfg2 0x7214&CR&&LF&
eth1: 00:03:7f:09:0b:ad&CR&&LF&
athrs26_reg_init_lan&CR&&LF&
ATHRS26: resetting s26&CR&&LF&
ATHRS26: s26 reset done&CR&&LF&
ag7240_phy_setup &CR&&LF&
eth1 up&CR&&LF&
eth0, eth1&CR&&LF&
Autobooting in 1 seconds&CR&&LF&
Connect the micro USB cable to power up the TP-WR703N router.
The messages on the right will starts to appear from the serial terminal program very fast.
06 Oct 201313 Sun 19:40:16.335 [TX] - tpl&CR&&LF&
06 Oct 201313 Sun 19:40:16.344 [RX] - hornet& &CR&
hornet& &CR&
Quickly key in "tpl" (enter key) into the console terminal, just as the messages reaches "Autobooting in 1 seconds"
You will be boot into rescue U-boot hornet,
and the prompt "hornet&" will be displayed.
"tpl" is not key in, the device will continue to boot into the router's
operation. If you are not fast enough the key in the "tpl", you can
unplug the USB to power off, and plug back the USB to restart the boot
up sequence. Be fast this time to key in "tpl".
06 Oct 201313 Sun 19:56:12.527 [TX] - tftpboot 0x wr703nv1_cn_3_12_11_up(110926).bin&CR&&LF&
06 Oct 201313 Sun 19:56:12.536 [RX] - tftpboot 0x wr703nv1_cn_3_12_11_up(110926).bin&CR&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
#################################################################&CR&&LF&
######################################################&CR&&LF&
done&CR&&LF&
Bytes transferred = c0000 hex)&CR&&LF&
Key in the following command (followed by enter key) in the serial console terminal to get the *.bin file from the TFTP server.
tftpboot 0x wr703nv1_cn_3_12_11_up(110926).bin
the Ethernet is properly connected, you will start to see a stream of
"#" responsing fast from the serial console terminal.
06 Oct 201313 Sun 19:56:14.764 [TX] - erase 0x9fx3c0000&CR&&LF&
06 Oct 201313 Sun 19:56:14.770 [RX] - erase 0x9fx3c0000&CR&
First 0x2 last 0x3d sector size 0x10000&CR&&LF&
&BS&&BS&&BS&&BS&
2&BS&&BS&&BS&&BS&
3&BS&&BS&&BS&&BS&
4&BS&&BS&&BS&&BS&
5&BS&&BS&&BS&&BS&
6&BS&&BS&&BS&&BS&
7&BS&&BS&&BS&&BS&
8&BS&&BS&&BS&&BS&
9&BS&&BS&&BS&&BS&
10&BS&&BS&&BS&&BS&
11&BS&&BS&&BS&&BS&
12&BS&&BS&&BS&&BS&
13&BS&&BS&&BS&&BS&
14&BS&&BS&&BS&&BS&
15&BS&&BS&&BS&&BS&
16&BS&&BS&&BS&&BS&
17&BS&&BS&&BS&&BS&
18&BS&&BS&&BS&&BS&
19&BS&&BS&&BS&&BS&
20&BS&&BS&&BS&&BS&
21&BS&&BS&&BS&&BS&
22&BS&&BS&&BS&&BS&
23&BS&&BS&&BS&&BS&
24&BS&&BS&&BS&&BS&
25&BS&&BS&&BS&&BS&
26&BS&&BS&&BS&&BS&
27&BS&&BS&&BS&&BS&
28&BS&&BS&&BS&&BS&
29&BS&&BS&&BS&&BS&
30&BS&&BS&&BS&&BS&
31&BS&&BS&&BS&&BS&
32&BS&&BS&&BS&&BS&
33&BS&&BS&&BS&&BS&
34&BS&&BS&&BS&&BS&
35&BS&&BS&&BS&&BS&
36&BS&&BS&&BS&&BS&
37&BS&&BS&&BS&&BS&
38&BS&&BS&&BS&&BS&
39&BS&&BS&&BS&&BS&
40&BS&&BS&&BS&&BS&
41&BS&&BS&&BS&&BS&
42&BS&&BS&&BS&&BS&
43&BS&&BS&&BS&&BS&
44&BS&&BS&&BS&&BS&
45&BS&&BS&&BS&&BS&
46&BS&&BS&&BS&&BS&
47&BS&&BS&&BS&&BS&
48&BS&&BS&&BS&&BS&
49&BS&&BS&&BS&&BS&
50&BS&&BS&&BS&&BS&
51&BS&&BS&&BS&&BS&
52&BS&&BS&&BS&&BS&
53&BS&&BS&&BS&&BS&
54&BS&&BS&&BS&&BS&
55&BS&&BS&&BS&&BS&
56&BS&&BS&&BS&&BS&
57&BS&&BS&&BS&&BS&
58&BS&&BS&&BS&&BS&
59&BS&&BS&&BS&&BS&
60&BS&&BS&&BS&&BS& 61&CR&&LF&
Erased 60 sectors&CR&&LF&
hornet& &CR&
First 0x2 last 0x3d sector size 0x10000&CR&&LF&
&BS&&BS&&BS&&BS&
2&BS&&BS&&BS&&BS&
3&BS&&BS&&BS&&BS&
4&BS&&BS&&BS&&BS&
5&BS&&BS&&BS&&BS&
6&BS&&BS&&BS&&BS&
7&BS&&BS&&BS&&BS&
8&BS&&BS&&BS&&BS&
9&BS&&BS&&BS&&BS&
10&BS&&BS&&BS&&BS&
11&BS&&BS&&BS&&BS&
12&BS&&BS&&BS&&BS&
13&BS&&BS&&BS&&BS&
14&BS&&BS&&BS&&BS&
15&BS&&BS&&BS&&BS&
16&BS&&BS&&BS&&BS&
17&BS&&BS&&BS&&BS&
18&BS&&BS&&BS&&BS&
19&BS&&BS&&BS&&BS&
20&BS&&BS&&BS&&BS&
21&BS&&BS&&BS&&BS&
22&BS&&BS&&BS&&BS&
23&BS&&BS&&BS&&BS&
24&BS&&BS&&BS&&BS&
25&BS&&BS&&BS&&BS&
26&BS&&BS&&BS&&BS&
27&BS&&BS&&BS&&BS&
28&BS&&BS&&BS&&BS&
29&BS&&BS&&BS&&BS&
30&BS&&BS&&BS&&BS&
31&BS&&BS&&BS&&BS&
32&BS&&BS&&BS&&BS&
33&BS&&BS&&BS&&BS&
34&BS&&BS&&BS&&BS&
35&BS&&BS&&BS&&BS&
36&BS&&BS&&BS&&BS&
37&BS&&BS&&BS&&BS&
38&BS&&BS&&BS&&BS&
39&BS&&BS&&BS&&BS&
40&BS&&BS&&BS&&BS&
41&BS&&BS&&BS&&BS&
42&BS&&BS&&BS&&BS&
43&BS&&BS&&BS&&BS&
44&BS&&BS&&BS&&BS&
45&BS&&BS&&BS&&BS&
46&BS&&BS&&BS&&BS&
47&BS&&BS&&BS&&BS&
48&BS&&BS&&BS&&BS&
49&BS&&BS&&BS&&BS&
50&BS&&BS&&BS&&BS&
51&BS&&BS&&BS&&BS&
52&BS&&BS&&BS&&BS&
53&BS&&BS&&BS&&BS&
54&BS&&BS&&BS&&BS&
55&BS&&BS&&BS&&BS&
56&BS&&BS&&BS&&BS&
57&BS&&BS&&BS&&BS&
58&BS&&BS&&BS&&BS&
59&BS&&BS&&BS&&BS&
60&BS&&BS&&BS&&BS& 61&CR&&LF&
Erased 60 sectors&CR&&LF&
After the bytes is successfully transferred, key in the following command (followed by enter key)
& erase 0x9fx3c0000
You will starts to see many more incoming data from the serial console terminal.
06 Oct 201313 Sun 19:56:42.981 [TX] - cp.b 0xx9fx3c0000&CR&&LF&
06 Oct 201313 Sun 19:56:42.990 [RX] - cp.b 0xx9fx3c0000&CR&
Copy to Flash... write addr: 9f020000&CR&&LF&
Then key in the following command (followed by enter key)
& cp.b 0xx9fx3c0000
06 Oct 201313 Sun 19:56:49.191 [TX] - bootm 9f020000&CR&&LF&
06 Oct 201313 Sun 19:56:55.697 [RX] - done&CR&&LF&
hornet& &CR&
Copy to Flash... write addr: 9f020000&CR&&LF&
done&CR&&LF&
hornet& bootm 9f020000&CR&
## Booting image at 9f020000 ...&CR&&LF&
Uncompressing Kernel Image ... OK&CR&&LF&
Starting kernel ...&CR&&LF&
Booting AR9330(Hornet)...&LF&
&NUL&&CR&
Linux version 2.6.31--LSDK-9.2.0.312 (root@bogon) (gcc version 4.3.3
(GCC) ) #149 Mon Sep 26 11:13:59 CST 2011&LF&&CR&
flash_size passed from bootloader = 4&LF&&CR&
CPU revision is:
(MIPS 24Kc)&LF&&CR&
Determined physical RAM map:&LF&&CR&
(usable)&LF&&CR&
User-defined physical RAM map:&LF&&CR&
(usable)&LF&&CR&
Zone PFN ranges:&LF&&CR&
0x -& 0x&LF&&CR&
Movable zone start PFN for each node&LF&&CR&
early_node_map[1] active PFN ranges&LF&&CR&
0: 0x -& 0x&LF&&CR&
Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 8128&LF&&CR&
Kernel command line: console=ttyS0,115200 root=31:02
rootfstype=squashfs init=/sbin/init
mtdparts=ar7240-nor0:128k(u-boot),1024k(kernel),2816(rootfs),64k(config),64k(ART)
mem=32M&LF&&CR&
PID hash table entries: 128 (order: 7, 512 bytes)&LF&&CR&
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)&LF&&CR&
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)&LF&&CR&
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.&LF&&CR&
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes&LF&&CR&
Writing ErrCtl register=&LF&&CR&
Readback ErrCtl register=&LF&&CR&
Memory: 2k available (1888k kernel code, 2904k reserved, 524k data, 116k init, 0k highmem)&LF&&CR&
Hierarchical RCU implementation.&LF&&CR&
NR_IRQS:128&LF&&CR&
plat_time_init: plat time init done&LF&&CR&
Calibrating delay loop... 266.24 BogoMIPS (lpj=532480)&LF&&CR&
Mount-cache hash table entries: 512&LF&&CR&
NET: Registered protocol family 16&LF&&CR&
===== ar7240_platform_init: 0&LF&&CR&
Whoops! This kernel is for product wr703 v1.0!&LF&&CR&
bio: create slab &bio-0& at 0&LF&&CR&
SCSI subsystem initialized&LF&&CR&
usbcore: registered new interface driver usbfs&LF&&CR&
usbcore: registered new interface driver hub&LF&&CR&
usbcore: registered new device driver usb&LF&&CR&
NET: Registered protocol family 2&LF&&CR&
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)&LF&&CR&
TCP established hash table entries: 1024 (order: 1, 8192 bytes)&LF&&CR&
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)&LF&&CR&
TCP: Hash tables configured (established 1024 bind 1024)&LF&&CR&
TCP reno registered&LF&&CR&
NET: Registered protocol family 1&LF&&CR&
AR7240 GPIOC major 0&LF&&CR&
squashfs: version 4.0 () Phillip Lougher&LF&&CR&
NTFS driver 2.1.29 [Flags: R/O].&LF&&CR&
msgmni has been set to 58&LF&&CR&
alg: No test for lzma (lzma-generic)&LF&&CR&
alg: No test for stdrng (krng)&LF&&CR&
io scheduler noop registered&LF&&CR&
io scheduler anticipatory registered&LF&&CR&
io scheduler deadline registered&LF&&CR&
io scheduler cfq registered (default)&LF&&CR&
driver, 1 ports, IRQ sharing disabled&LF&&CR&
ttyS0: detected caps
should be &LF&&CR&
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A&LF&&CR&
console [ttyS0] enabled&LF&&CR&
PPP generic driver version 2.4.2&LF&&CR&
NET: Registered protocol family 24&LF&&CR&
cmdlinepart partition parsing not available&LF&&CR&
set partition boot &LF&&CR&
set partition kernel &LF&&CR&
set partition rootfs &LF&&CR&
set partition config &LF&&CR&
set partition art &LF&&CR&
set partition