NISE 100 User Manual()_甜梦文库
NISE 100 User Manual()
NEXCOM International Co., Ltd.Industrial Computing Solutions Fan-less Computer NISE 100 User ManualNEXCOM International Co., Ltd. Published September 2009ContentsContentsPrefaceCopyright ............................................................................................. iv Disclaimer ............................................................................................. iv Acknowledgements .............................................................................. iv Regulatory Compliance Statements ....................................................... iv Declaration of Conformity...................................................................... iv RoHS Compliance ................................................................................... v Warranty and RMA ................................................................................ vi Safety Information ................................................................................vii Installation Recommendations................................................................vii Safety Precautions.................................................................................viii Technical Support and Assistance ........................................................... ix Conventions Used in this Manual ........................................................... ix Global Service Contact Information ......................................................... x Package Contents ..................................................................................xii Ordering Information ............................................................................xiiiChapter 2: Jumpers And ConnectorsBefore You Begin ....................................................................................5 Precautions .............................................................................................5 Jumper Settings ......................................................................................6 Locations of the Jumpers and Connectors ...............................................7 Jumpers ................................................................................................8 Clear CMOS Select .............................................................................8 Power Mode Select ............................................................................8 Backlight & Panel Power Select ...........................................................9 Backlight Enable Select .......................................................................9 KB/MS Connector Select...................................................................10 USB Power Select .............................................................................10 Connector Pin Definitions ...................................................................11 External I/O Interface ........................................................................11 Status Indicators.............................................................................11 Power Switch .................................................................................11 +12V DC Input...............................................................................12 USB Ports .......................................................................................12 LAN Port ........................................................................................13 COM1 (RS232/422/485) Connector................................................13 PS/2 Keyboard/Mouse Port .............................................................14 DVI-I Port .......................................................................................14Chapter 1: Product IntroductionOverview ................................................................................................1 Hardware Specifications ..........................................................................2 Getting to Know NISE Series ...................................................................3 Front Panel ...........................................................................................3 Rear Panel ............................................................................................3 Mechanical Dimensions...........................................................................4Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.iiNISE 100 User ManualContentsInternal Connectors ..........................................................................15 +12V Power Input Connector.........................................................15 Panel Backlight Connector .............................................................15 FP1 Connector ...............................................................................16 FP2 Connector ...............................................................................16 SATA Connector.............................................................................17 Serial ATA and HDD Power Connectors ..........................................17 USB 2.0 Port 2,3 Connector ...........................................................18 USB 2.0 Port 4,5 Connector ...........................................................18 USB 2.0 Port 6,7 Connector ...........................................................19 COM2 (RS232) Connector .............................................................19 COM3 (RS232) Connector .............................................................20 COM4 (RS232) Connector .............................................................20 Audio Output Connector ...............................................................21Chapter 4: BIOS SetupAbout BIOS Setup .................................................................................29 When to Configure the BIOS.................................................................29 Default Configuration ...........................................................................30 Entering Setup ......................................................................................30 Legends ................................................................................................30 BIOS Setup Utility ..................................................................................31 Main ..................................................................................................31 Advanced ...........................................................................................32 Boot ...................................................................................................36 Chipset ...............................................................................................37 Power .................................................................................................39 Security ..............................................................................................41 Exit .....................................................................................................42Chapter 3: System SetupRemoving the Chassis Cover ................................................................22 Installing the SODIMM ..........................................................................23 Installing a SATA Hard Drive ..................................................................25Appendix A: Power ConsumptionTest Environment ..................................................................................43 Test Result.............................................................................................44Appendix B: GPI/O Programming GuideGPI/O Programming Guide ....................................................................45Appendix C: Watchdog Timer SettingWatchdog Timer Setting .......................................................................47Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.iiiNISE 100 User ManualPrefacePrefaceCopyrightThis publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co., Ltd.Regulatory Compliance StatementsThis section provides the FCC compliance statement for Class A devices and describes how to keep the system CE compliant.Declaration of ConformityFCC This equipment has been tested and verified to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area (domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense. CE The product(s) described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.DisclaimerThe information in this document is subject to change without prior notice and does not represent commitment from NEXCOM International Co., Ltd. However, users may update their knowledge of any product in use by constantly checking its manual posted on our website: http://www.nexcom. com. NEXCOM shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of any product, nor for any infringements upon the rights of third parties, which may result from such use. Any implied warranties of merchantability or fitness for any particular purpose is also disclaimed.AcknowledgementsNISE 100 is a trademark of NEXCOM International Co., Ltd. All other product names mentioned herein are registered trademarks of their respective owners.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.ivNISE 100 User ManualPrefaceRoHS ComplianceNEXCOM RoHS Environmental Policy and Status Update NEXCOM is a global citizen for building the digital infrastructure. We are committed to providing green products and services, which are compliant with European Union RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment) directive 2002/95/EU, to be your trusted green partner and to protect our environment. RoHS restricts the use of Lead (Pb) & 0.1% or 1,000ppm, Mercury (Hg) & 0.1% or 1,000ppm, Cadmium (Cd) & 0.01% or 100ppm, Hexavalent Chromium (Cr6+) & 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) & 0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) & 0.1% or 1,000ppm. In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force in to implement the introduction of green products. The task force will ensure that we follow the standard NEXCOM development procedure and that all the new RoHS components and new manufacturing processes maintain the highest industry quality levels for which NEXCOM are renowned. The model selection criteria will be based on market demand. Vendors and suppliers will ensure that all designed components will be RoHS compliant.How to recognize NEXCOM RoHS Products? For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name. All new product models launched after January 2006 will be RoHS compliant. They will use the usual NEXCOM naming convention.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.vNISE 100 User ManualPrefaceWarranty and RMANEXCOM Warranty Period NEXCOM manufactures products that are new or equivalent to new in accordance with industry standard. NEXCOM warrants that products will be free from defect in material and workmanship for 2 years, beginning on the date of invoice by NEXCOM. HCP series products (Blade Server) which are manufactured by NEXCOM are covered by a three year warranty period. NEXCOM Return Merchandise Authorization (RMA) ? Customers shall enclose the “NEXCOM RMA Service Form” with the returned packages. ? Customers must collect all the information about the problems encountered and note anything abnormal or, print out any on-screen messages, and describe the problems on the “NEXCOM RMA Service Form” for the RMA number apply process. ? Customers can send back the faulty products with or without accessories (manuals, cable, etc.) and any components from the card, such as CPU and RAM. If the components were suspected as part of the problems, please note clearly which components are included. Otherwise, NEXCOM is not responsible for the devices/parts. ? Customers are responsible for the safe packaging of defective products, making sure it is durable enough to be resistant against further damage and deterioration during transportation. In case of damages occurred during transportation, the repair is treated as “Out of Warranty.” ? Any products returned by NEXCOM to other locations besides the customers’ site will bear an extra charge and will be billed to the customer. Repair Service Charges for Out-of-Warranty Products NEXCOM will charge for out-of-warranty products in two categories, one is basic diagnostic fee and another is component (product) fee. System Level ? Component fee: NEXCOM will only charge for main components such as SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistor, capacitor. ? Items will be replaced with NEXCOM products if the original one cannot be repaired. Ex: motherboard, power supply, etc. ? Replace with 3rd party products if needed. ? If RMA goods can not be repaired, NEXCOM will return it to the customer without any charge. Board Level ? Component fee: NEXCOM will only charge for main components, such as SMD chip, BGA chip, etc. Passive components will be repaired for free, ex: resistors, capacitors. ? If RMA goods can not be repaired, NEXCOM will return it to the customer without any charge.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.viNISE 100 User ManualPrefaceWarningsRead and adhere to all warnings, cautions, and notices in this guide and the documentation supplied with the chassis, power supply, and accessory modules. If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules, contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements.Installation RecommendationsEnsure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated. Adequate lighting and proper tools can prevent you from accidentally damaging the internal components. Most of the procedures that follow require only a few simple tools, including the following: ?
A Philips screwdriver A flat-tipped screwdriver A grounding strap An anti-static padCautionsElectrostatic discharge (ESD) can damage system components. Do the described procedures only at an ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis.Safety InformationBefore installing and using the device, note the following precautions: ? Read all instructions carefully. ? Do not place the unit on an unstable surface, cart, or stand. ? Follow all warnings and cautions in this manual. ? When replacing parts, ensure that your service technician uses parts specified by the manufacturer. ? Avoid using the system near water, in direct sunlight, or near a heating device. ? The load of the system unit does not solely rely for support from the rackmounts located on the sides. Firm support from the bottom is highly necessary in order to provide balance stability. ? The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.Using your fingers can disconnect most of the connections. It is recommended that you do not use needlenose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.viiNISE 100 User ManualPrefaceSafety Precautions1. 2. 3. 4. 5. 6. 7. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from humidity. Put this equipment on a stable surface during installation. Dropping it or letting it fall may cause damage. Do not leave this equipment in either an unconditioned environment or in a above 40oC storage temperature as this may damage the equipment. The openings on the enclosure are for air convection to protect the equipment from overheating. DO NOT COVER THE OPENINGS. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.12. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 13. Never pour any liquid into an opening. This may cause fire or electrical shock. 14. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 15. If one of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 16. Do not place heavy objects on the equipment. 17. The unit uses a three-wire ground cable which is equipped with a third pin to ground the unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does not support this kind of plug, contact your electrician to replace your obsolete outlet. 18. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. 19. The computer is provided with CD drives that comply with the appropriate safety standards including IEC 60825.8. 9.10. Place the power cord in a way so that people will not step on it. Do not place anything on top of the power cord. Use a power cord that has been approved for use with the product and that it matches the voltage and current marked on the product’s electrical range label. The voltage and current rating of the cord must be greater than the voltage and current rating marked on the product. 11. All cautions and warnings on the equipment should be noted.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.viiiNISE 100 User ManualPrefaceTechnical Support and Assistance1. For the most updated information of NEXCOM products, visit NEXCOM’s website at . 2. For technical issues that require contacting our technical support team or sales representative, please have the following information ready before calling: C Product name and serial number C Detailed information of the peripheral devices C Detailed information of the installed software (operating system, version, application software, etc.) C A complete description of the problem C The exact wordings of the error messages Warning! 1. Handling the unit: carry the unit with both hands and handle it with care. 2. Maintenance: to keep the unit clean, use only approved cleaning products or clean with a dry cloth. 3. CompactFlash: Turn off the unit’s power before inserting or removing a CompactFlash storage card.Conventions Used in this ManualWarning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task. Caution: Information to avoid damaging components or losing data. Note: Provides additional information to complete a task easily.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.ixNISE 100 User ManualPrefaceGlobal Service Contact InformationHeadquarters Taiwan18F, No. 716, Chung-Cheng Rd. Chung-Ho City, Taipei County 235, Taiwan, R.O.C. Tel: +886-2- Fax: +886-2- .twGermanyLeopoldstrase Business Centre, Leopoldstrase 244 80807 Munich, Germany Tel: +49-89- Fax: +49-89- http://www.nexcom.euItalyVia Gaudenzio Ferrari 29, 21047 Saronno (VA) Italia Tel: +39 02
Fax: +39 02
http://www.nexcom.euUSA3758 Spinnaker Court, Fremont, CA 94538, USA Tel: +1-510-656-2248 Fax: +1-510-656-2158 United Kingdom10 Vincent Avenue, Crownhill Business Centre Milton Keynes, Buckinghamshire, MK8 0AB United Kingdom Tel: +44- Fax: +44- http://www.nexcom.euFranceZ.I. des Amandiers, 17, Rue des entrepreneurs 78420 Carrières sur Seine, France Tel: +33 (0)1 71 51 10 20 Fax: +33 (0)1 71 51 10 21 http://www.nexcom.euCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.xNISE 100 User ManualPrefaceChina-BeijingRoom 301, Block E, Power Creative Building, No. 1 Shangdi East Rd. Haidian Dist., Beijing, 100085, China Tel: +86-10- Fax: +86-10- Japan10F, Nakagin-Shiroyama Building, 8-16-13. Ginza Chuou-ku, Tokyo 104-0061, Japan Tel: +81-3- Fax: +81-3- http://www.China-Shanghai OfficeRoom 1505, Greenland He Chuang Building, No. 450 Caoyang Rd. Shanghai, 200063, China Tel: +86-21- Fax: +86-21- China-Nanjing OfficeHall C, Block 17, TianXingCuiLang, No. 49 Yunnan North Rd. Nanjing, 210018, China Tel: +86-25- Fax: +86-25- China-Shenzhen OfficeWestern Room 708, Block 210, Tairan Industry & Trading Place, Futian Area, Shenzhen, China 518040 TEL: +86-755-833 27203 FAX: +86-755-833 27213 Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.xiNISE 100 User ManualPrefacePackage contentsBefore continuing, verify that the NISE 100 package that you received is complete. Your package should have all the items listed in the following table. Item 1 2 3 4 5 6 7 8 P/N X00 X00 X00 X00 6 602DCD X00 PE ZIPPER BAG #8 PE ZIPPER BAG #3 NISE100 QUICK REFERENCE GUIDE VER:A PS/2 Y CABLE NISE100 CD DRIVER VER:1.0 POWER ADAPTER 60W 12V/5A DVI-I TO VGA ADAPTER Description FLAT HEAD SCREW LONG FOR HDD USE Qty 4 1 1 1 1 1 1 1Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.xiiNISE 100 User ManualPrefaceordering informationThe following provides ordering information for NISE 100. ?
Barebone NISE 100-M01G-S80G (P/N: 10J) - Intel? Atom? N270 Fanless SystemCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.xiiiNISE 100 User ManualChapter 1: Product IntroductionChapter 1: produCt IntroduCtIonOverviewFrontRearKey Features ?
Onboard Intel? Atom? N270 processor, 1.6GHz ?
Intel? 945GSE chipset ?
1 x 10/100/1000 Mbps LAN port ?
2 x USB 2.0 ports ?
1 x DVI-I port ?
1 x Keyboard/Mouse port ?
1 x RS232/422/485 and 2 x RS232 ?
Onboard DC to DC power design to support +12V DC power input ?
Supports ATX power modeCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.1NISE 100 User ManualChapter 1: Product IntroductionHardware SpecificationsMain Board ?
Onboard Intel? Atom? N270 processor, 1.6GHz ?
Supports 533MHz FSB ?
Intel? 945GSE and ICH7M chipsets Main Memory ?
One DDR2 SODIMM socket ?
Single channel ?
Supports up to 2GB DDR2 400/533 SDRAM, unbuffered, non-ECC I/O Interface - Front ?
HDD Access LED ?
Power status LED ?
2 x RS232 ports ?
ATX Power on/off switch I/O Interface - Rear ?
1 x DVI-I port ?
1 x PS/2 keyboard/mouse port ?
1 x RS232/422/485 port ?
1 x 10/100/1000 LAN port ?
2 x USB 2.0 ports ?
+12V DC power inputStorage ?
1 x internal 2.5” SATA HDD drive bay Power Requirements ?
DC to DC power designed for onboard support of +12V DC ?
1 x external 60W AC/DC lockable power adapter Power input: 100V to 240V AC 2A 50/60 Hz Power output: 12V DC Dimensions ?
185mm (W) x 132mm (D) x 50mm (H) (7.28” x 5.2” x 1.97”) Construction ?
Aluminum chassis with fan-less design Environment ?
Operating temperature: Ambient with airflow: -5°C to 55°C (According to IEC, IEC, IEC) ?
Storage temperature: -20°C to 80°C ?
Relative humidity: 10% to 93% (Non-Condensing) Certifications ?
CE approval ?
FCCCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.2NISE 100 User ManualChapter 1: Product IntroductionGetting to Know NISE 100Front PanelRear PanelPower LED HDD LED Power on/off switch COM COM +12V DC Input USB LAN COM PS/2 DVI-I+12V DC Input Used to plug a DC power cord. USB Used to connect USB 2.0/1.1 devices. LAN Used to connect the system to a local area network. COM The COM port supports RS232/422/485 compatible serial devices. PS/2 Used to connect a PS/2 keyboard/mouse device. DVI-I Used to connect a digital LCD panel.Power On/Off Switch Press to power-on or power-off the system. COM Ports The COM ports support RS232 compatible serial devices. Power LED Indicates the power status of the system. HDD LED Indicates the status of the hard drive.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.3NISE 100 User ManualChapter 1: Product IntroductionMechanical Dimensions83.0 40.0 12.5 60.0 12.5156.0206.0175.050.0185.0194.0194.025.0 94.0 120.0 120.060.056.056.0115.0Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.4COM4COM1 DVI-ICOM31+12V DCNISE 100 User ManualChapter 2: Jumpers and ConnectorsChapter 2: Jumpers and ConneCtorsThis chapter describes how to set the jumpers on the motherboard. Note that the following procedures are generic for all NISE 100 series. tronic components. Humid environment tend to have less static electricity than dry environments. A grounding strap is warranted whenever danger of static electricity exists.Before You Begin?
Ensure you have a stable, clean working environment. Dust and dirt canget into components and cause a malfunction. Use containers to keep small components separated.PrecautionsComputer components and electronic circuit boards can be damaged by discharges of static electricity. Working on the computers that are still connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to your computer or yourself:?
Adequate lighting and proper tools can prevent you from accidentallydamaging the internal components. Most of the procedures that follow require only a few simple tools, including the following:?
A Philips screwdriver ?
A flat-tipped screwdriver ?
A set of jewelers Screwdrivers ?
A grounding strap ?
An anti-static pad?
Always disconnect the unit from the power outlet whenever you areworking inside the case.?
If possible, wear a grounded wrist strap when you are working insidethe computer case. Alternatively, discharge any static electricity by touching the bare metal chassis of the unit case, or the bare metal body of any other grounded appliance.?
Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nosed pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors.?
Hold electronic circuit boards by the edges only. Do not touch the components on the board unless it is necessary to do so. Don’t flex or stress the circuit board.?
Before working on internal components, make sure that the poweris off. Ground yourself before touching any internal components, by touching a metal object. Static electricity can damage many of the elec-?
Leave all components inside the static-proof packaging that theyshipped with until they are ready for installation.?
Use correct screws and do not over tighten screws.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.5NISE 100 User ManualChapter 2: Jumpers and ConnectorsJumper SettingsA jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open. Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off). Two-Pin Jumpers: Open (Left) and Short (Right)Three-Pin Jumpers: Pins 1 and 2 Are ShortCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.6NISE 100 User ManualChapter 2: Jumpers and ConnectorsLocations of the Jumpers and ConnectorsThe figure on the right is the main board used in the NISE 100 system. It shows the locations of the jumpers and connectors.AUDIO1 JP1 FP2 FP1 CN4 CN3 CN5 JP2 COM1 CN6 COM3 ATX1 SATA1 SATA2LVDS PCI1CN1 BAT1 USB4 USB3 USB2 JP6 USB1 LAN1 COM1 CN7 CN2 COM2 JP3 JP4 JP5Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.7NISE 100 User ManualChapter 2: Jumpers and ConnectorsJumpersClear CMOS Select Connector size: 1x2, 2.54mm Connector location: JP11 2 Pin Open Short Definition Normal Operation (default) Clear CMOSPower Mode Select Connector size: 1x2, 2.54mm Connector location: JP21 2 Pin Open Short Definition AT Mode ATX Mode (default)Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.8NISE 100 User ManualChapter 2: Jumpers and ConnectorsBacklight & Panel Power Select Connector size: 2x3, 2.54mm Connector location: JP35 3 1Backlight Enable Select Connector size: 1x3, 2.0mm Connector location: JP41 3 Pin 1-2 2-3 Definition Active High (default) Active Low6 4 2 Settings 1 2 1-3 3-5 2-4 4-6 Status Backlight Power = +12V (default) Backlight Power = +5V Panel Power = +3.3V (default) Panel Power = +5V (default)Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.9NISE 100 User ManualChapter 2: Jumpers and ConnectorsKB/MS Connector Select Connector size: 2x5, 2.54mm Connector location: JP52 1 Pin 1 3 5 7 9 10 9 Definition +5VSB KBCLK_SIO KBCLK_CN7 MSCLK_SIO MSCLK_CN7 Pin 2 4 6 8 10 Definition GND KBDAT_ SIO KBDAT_CN7 MSDAT_SIO MSDAT_CN7USB Power Select Connector size: 1x3, 2.0mm Connector location: JP61 3 Pin 1-2 2-3 Definition +5VSB (default) +5VCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.10NISE 100 User ManualChapter 2: Jumpers and ConnectorsConnector Pin DefinitionsExternal I/O InterfaceStatus IndicatorsPWRPower Switch Button ATX switch, unlockHDD Status PWR HDD LED Color Green YellowCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.11NISE 100 User ManualChapter 2: Jumpers and Connectors+12V DC Input Connector size: 4-pin power jack, 15x16x17.4mm Connector location: ATX12 4USB Ports Connector size: Dual USB port, Type A Connector location: USB11 5 4 81 3Pin 1 3Definition GND +12VPin 2 4Definition GND +12VPin 1 2 3 4Definition +5V USB1USB1+ GNDPin 5 6 7 8Definition +5V USB0USB0+ GNDCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.12NISE 100 User ManualChapter 2: Jumpers and ConnectorsLAN Port Connector size: RJ45 port with LEDs Connector location: LAN1Act 8 LinkCOM1 (RS232/422/485) Connector Connector size: DB-9 Connector location: COM11 59 16Connector Pin Definition Pin 1 2 3 4 Definition Tx+ TxRx+ NC Pin 5 6 7 8 Definition NC RxNC NC Pin 1 2 3 4 5 6 7 8 9 RS232 DCD (Data Carrier Detect) RXD (Receive Data) TXD (Transmit Data) DTR (Data Terminal Ready) GND (Ground) DSR (Data Set Ready) RTS (Request to Send) CTS (Clear to Send) RI (Ring indicator) RS422 TXRX+ TX+ RXGND N/A N/A N/A N/A RS485 Half Duplex DATAN/A DATA+ N/A GND N/A N/A N/A N/ACopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.13NISE 100 User ManualChapter 2: Jumpers and ConnectorsPS/2 Keyboard/Mouse Port Connector size: PS/2, Mini-DIN-6 Connector location: CN78 5 2 1 6 3DVI-I Port Connector size: 24-pin D-Sub Connector location: CN21 817 Pin 1 3 5 Definition KBDAT GND KBCLK Pin 2 4 6 Definition MSDAT +5V MSCLK Pin 1 3 5 7 9 11 13 15 17 19 21 2324 Function TX2N GND TX5P SD_DATA TX1N GND TX4P VGA_EN TX0N GND TX6P TCLP Pin 2 4 6 8 10 12 14 16 18 20 22 24 Function TX2P TX5N SD_CLK VSYNC TX1P TX4N VGA_PWR HPD TX0P TX6N GND TXLNCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.14NISE 100 User ManualChapter 2: Jumpers and ConnectorsInternal Connectors+12V Power Input Connector Connector size: 2x2 Connector location: ATX11 3 2 4Panel Backlight Connector Connector size: JST 7-pin, Pitch: 1.25mm Connector location: CN17Pin 1 2 3 4Definition GND GND +12V +12V1 Pin 1 2 3 4 5 6 7 Definition N.C. BL_ADJ GND +5V / +12V ** +5V / +12V ** GND BL_EN / BL_EN# ** denotes selected by JP4 ** denotes selected by JP3Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.15NISE 100 User ManualChapter 2: Jumpers and ConnectorsFP1 Connector Connector size: 8-pin, Pitch: 2.54mm Connector location: FP11 7 Pin 1 3 5 7 2 8FP2 Connector Connector size: 10-pin, Pitch: 2.54mm Connector location: FP21 29 Definition Reset Button + Reset Button HDD LED + HDD LED Pin 2 4 6 8 Definition Speaker + N.C. N.C. Speaker Pin 1 3 5 7 910 Definition Power LED + NC Power LED Keyboard Lock GND Pin 2 4 6 8 10 Definition Power Button + Power Button N.C. SMBus Data SMBus ClockCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.16NISE 100 User ManualChapter 2: Jumpers and ConnectorsSATA Connector Connector size: Standard Serial ATAII 7P (1.27mm) Connector location: SATA21 7Serial ATA and HDD Power Connectors Connector size: Standard Serial ATAII 7P+15P MALE 180D Connector location: SATA1S1 S7 P1 P15Pin 1 2 3 4 5 6 7Definition GND TX+ TXGND RXRX+ GND Pin S1 S2 S3 S4 S5 S6 S7 Definition GND TX+ TXGND RXRX+ GND Pin P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 Definition +3.3V +3.3V +3.3V GND GND GND +5V +5V +5V GND GND GND +12V +12V +12VCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.17NISE 100 User ManualChapter 2: Jumpers and ConnectorsUSB 2.0 Port 2,3 Connector Connector size: 10-pin, 2.54mm Connector location: USB22 1 Pin 1 3 5 7 9 10 9 Definition +5V USB2USB2+ GND KEY Pin 2 4 6 8 10 Definition +5V USB3USB3+ GND GNDUSB 2.0 Port 4,5 Connector Connector size: 10-pin, 2.54mm Connector location: USB32 1 Pin 1 3 5 7 9 10 9 Definition +5V USB4USB4+ GND KEY Pin 2 4 6 8 10 Definition +5V USB5USB5+ GND GNDCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.18NISE 100 User ManualChapter 2: Jumpers and ConnectorsUSB 2.0 Port 6,7 Connector Connector size: 10-pin, 2.54mm Connector location: USB41 2COM2 (RS232) Connector Connector size: 10-pin, Pitch: 1.25mm Connector location: COM210 19 Pin 1 3 5 7 910 Definition +5V USB6USB6+ GND KEY Pin 2 4 6 8 10 Definition +5V USB7USB7+ GND GNDPin 1 2 3 4 5 6 7 8 9 10Definition DCD (Data Carrier Detect) DSR (Data Set Ready) RXD (Receive Data) RTS (Request To Send) TXD (Transmit Data) CTS (Clear To Send) DTR (Data Terminal Ready) RI (Ring Indicator) GND (Ground) +5VCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.19NISE 100 User ManualChapter 2: Jumpers and ConnectorsCOM3 (RS232) Connector Connector size: DB-9 Connector location: COM31 5COM4 (RS232) Connector Connector size: 10-pin, Pitch: 1.25mm Connector location: COM310 1Connector size: DB-9 Connector location: COM41 5Connector size: 10-pin, Pitch: 1.25mm Connector location: COM410 19696Pin 1 2 3 4 5 6 7 8 9 10Definition DCD (Data Carrier Detect) DSR (Data Set Ready) RXD (Receive Data) RTS (Request To Send) TXD (Transmit Data) CTS (Clear To Send) DTR (Data Terminal Ready) RI (Ring Indicator) GND (Ground) +5VPin 1 2 3 4 5 6 7 8 9 10Definition DCD (Data Carrier Detect) DSR (Data Set Ready) RXD (Receive Data) RTS (Request To Send) TXD (Transmit Data) CTS (Clear To Send) DTR (Data Terminal Ready) RI (Ring Indicator) GND (Ground) +5VCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.20NISE 100 User ManualChapter 2: Jumpers and ConnectorsAudio Output Connector Connector size: 6-pin, Pitch: 2.5mm Connector location: AUDIO11 6Pin 1 2 3 4 5 6Definition LOUT_R GND LOUT_L LIN_R MIC LIN_LCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.21NISE 100 User ManualChapter 3: System SetupChapter 3: SyStem SetupRemoving the Chassis CoverPrior to removing the chassis cover, make sure the unit’s power is off and disconnected from the power sources to prevent electric shock or system damage. This chapter will guide you on installing the SODIMM and SATA drive. You need to remove the bottom cover to access the DIMM socket and SATA cables. 1. Remove the bottom cover’s mounting screws then put them in a safe place for later use.2. Lift up the cover then remove it from the chassis.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.22NISE 100 User ManualChapter 3: System SetupInstalling the SODIMM1. Locate the SODIMM socket on the board.SODIMM socket2. Insert the module into the socket at an approximately 30 degrees angle. Apply firm even pressure to each end of the module until it slips into the socket. The gold-plated connector on the edge of the module will almost completely disappear inside the socket.SODIMM socket SODIMMCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.23NISE 100 User ManualChapter 3: System Setup3. Push the module down until the clips on both sides of the socket lock into position. You will hear a distinctive “click”, indicating the module is correctly locked into position.ClipClipCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.24NISE 100 User ManualChapter 3: System SetupInstalling a SATA Hard Drive1. With the bottom side of the chassis facing up, remove the screws of the bottom cover.2. Upon removing the chassis cover, turn it to the other side. This will be the inner side of the cover. This is where you will attach the SATA drive. The 4 mounting holes for the SATA drive are shown below.Mounting holeCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.25NISE 100 User ManualChapter 3: System Setup3. Align the mounting holes of the SATA drive with the mounting holes on the cover.4. Now turn the cover to the other side. This will be the outer side of the cover. Use the provided screws to secure the drive to the chassis.SATA driveCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.26NISE 100 User ManualChapter 3: System Setup5. The SATA data cable and the SATA power cable are readily accessible upon removing the chassis cover.6. Connect the SATA data cable and SATA power cable to the connectors on the SATA drive.SATA data cable SATA power cable SATA data cable SATA power cableCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.27NISE 100 User ManualChapter 3: System Setup7. Replace the cover then mount back the screws you removed in step 1.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.28NISE 100 User ManualChapter 4: BIOS SetupChapter 4: BIOS SetupThis chapter describes how to use the BIOS setup program for NISE 100. The BIOS screens provided in this chapter are for reference only and may change if the BIOS is updated in the future. To check for the latest updates and revisions, visit the NEXCOM Web site at .tw. The settings made in the setup program affect how the computer performs. It is important, therefore, first to try to understand all the Setup options, and second, to make settings appropriate for the way you use the computer.When to Configure the BIOSThis program should be executed under the following conditions:About BIOS SetupThe BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to suit your individual work needs. It is a ROM-based configuration utility that displays the system’s configuration status and provides you with a tool to set system parameters. These parameters are stored in non-volatile battery-backed-up CMOS RAM that saves this information even when the power is turned off. When the system is turned back on, the system is configured with the values found in CMOS. With easy-to-use pull down menus, you can configure such items as:? ? ? ? ? ?When changing the system configuration When a configuration error is detected by the system and you are prompted to make changes to the Setup program When resetting the system clock When redefining the communication ports to prevent any conflicts When making changes to the Power Management configuration When changing the password or making other changes to the security setupNormally, CMOS setup is needed when the system hardware is not consistent with the information contained in the CMOS RAM, whenever the CMOS RAM has lost power, or the system features need to be changed.? ? ? ?Hard drives, diskette drives, and peripherals Video display type and display options Password protection from unauthorized use Power management featuresCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.29NISE 100 User ManualChapter 4: BIOS SetupDefault ConfigurationMost of the configuration settings are either predefined according to the Load Optimal Defaults settings which are stored in the BIOS or are automatically detected and configured without requiring any actions. There are a few settings that you may need to change depending on your system configuration.LegendsKey Right and Left arrows Up and Down arrows &Esc& + (plus key) - (minus key) Tab &F1& &F10& &Enter& Function Moves the highlight left or right to select a menu. Moves the highlight up or down between submenus or fields. Exits to the BIOS Setup Utility. Scrolls forward through the values or options of the highlighted field. Scrolls backward through the values or options of the highlighted field. Selects a field. Displays General Help. Saves and exits the Setup program. Press &Enter& to enter the highlighted submenu.Entering SetupWhen the system is powered on, the BIOS will enter the Power-On Self Test (POST) routines. These routines perform vario if an error is encountered, the error will be reported in one of two different ways:? ?If the error occurs before the display device is initialized, a series of beeps will be transmitted. If the error occurs after the display device is initialized, the screen will display the error message.Powering on the computer and immediately pressing &Del& allows you to enter Setup. Another way to enter Setup is to power on the computer and wait for the following message during the POST:TO ENTER SETUP BEFORE BOOT PRESS &CTRL-ALT-ESC& Press the &Del& key to enter Setup:Scroll Bar When a scroll bar appears to the right of the setup screen, it indicates that there are more available fields not shown on the screen. Use the up and down arrow keys to scroll through all the available fields. Submenu When “u“ appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press &Enter&.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.30NISE 100 User ManualChapter 4: BIOS SetupBIOS Setup UtilityOnce you enter the AMI BIOS Setup Utility, the Main Menu will appear on the screen. The main menu allows you to select from six setup functions and one exit choices. Use arrow keys to select among the items and press &Enter& to accept or enter the submenu.System Date The date format is &day&, &month&, &date&, &year&. Day displays a day, from Sunday to Saturday. Month displays the month, from January to December. Date displays the date, from 1 to 31. Year displays the year, from 1999 to 2099. System Time The time format is &hour&, &minute&, &second&. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays minutes from 00 to 59. Second displays seconds from 00 to 59. Primary IDE Master, Primary IDE Slave and Third IDE Master When you enter the BIOS Setup Utility, the BIOS will auto detect the existing IDE devices then displays the status of the detected devices. To configure an IDE drive, move the cursor to a field then press &Enter&. You can select the Type, PIO mode, DMA mode, etc.←→ ↑↓MainThe Main menu is the first screen that you will see when you enter the BIOS Setup Utility.Main System Date System Timeu
Primary IDE Master u
Primary IDE Slave u
Third IDE Master u
SystemAdvancedBootBIOS SETUP UTILITY Chipset Power [Tue 08/25/2009] [14:06:01] : [Not Detected] : [Not Detected] : [Not Detected]SecurityExitInformation+Tab F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Change Field Select Field General Help Save and Exit ExitSystem Information Move the cursor to this field then press &Enter&. This section displays general system specifications. The BIOS automatically detects the information in this section.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.31NISE 100 User ManualChapter 4: BIOS SetupAdvancedThe Advanced menu allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference. Setting incorrect field values may cause the system to malfunction.BIOS SETUP UTILITY Boot Chipset PowerOnboard Peripherals Configuration This section is used to configure USB devices, the audio controller, LAN controller, PCIE, etc. Trusted Computing This section is used to further configure the system. Hardware Health Configuration This section is used to configure the hardware monitoring events such as temperature, fan speed and voltages.MainAdvancedSecurity Configure CPU.ExitAdvanced Settings WARNING: Setting wrong values in below sections may cause system to malfunction.u
I/O Configuration u
OnBoard Peripherals Configuration u
Trusted Computing u
Hardware Health Configuration←→ ↑↓Enter F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Go to Sub Screen General Help Save and Exit ExitI/O Configuration This section is used to configure the I/O functions such as the COM ports supported by the onboard Super I/O chip.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.32NISE 100 User ManualChapter 4: BIOS SetupOnboard I/O Configuration This section is used to configure the COM ports.BIOS SETUP UTILITY Advanced Onboard I/O Configuration COM1 Address COM1 IRQ COM1 Function Type COM1 Pin9 Voltage COM2 Address COM2 IRQ COM2 Pin9 Voltage COM3 Address COM3 IRQ COM3 Mode COM3 Pin9 Voltage COM4 Address COM4 IRQ COM4 Mode COM4 Pin9 Voltage [3F8] [4] [RS232] [Normal] [2F8] [4] [Normal] [3E8] [11] [Normal] [Normal] [2E8] [11] [Normal] [Normal] Allows BIOS to Select Serial Port1 Base Addresses.Onboard Peripherals Configuration Settings This section is used to configure the onboard controllers.BIOS SETUP UTILITY Advanced Onboard Peripherals Configuration Settings USB Controller USB Device Legacy Support USB 2.0 Controller Audio Controller Onboard LAN Controller Onboard LAN OPTROM PCIE Port Configuration u
On-Chip ATA Devices [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Disabled] [1 Port 4L] Disabled Enabled←→ ↑↓+F1 F10 ESCSelect Screen Select Item Change Option General Help Save and Exit Exit←→ ↑↓+F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Change Option General Help Save and Exit Exitv02.61 (C)Copyright , American Megatrends, Inc.COM1 Address, COM2 Address, COM3 Address, COM4 Address These fields are used to select the serial port’s base address. COM1 IRQ, COM2 IRQ, COM3 IRQ, COM4 IRQ These fields are used to select the serial port’s IRQ.USB Controller This field is used to enable or disable the USB controller. USB Device Legacy Support Due to the limited space of the BIOS ROM, the support for legacy USB keyboard (in DOS mode) is by default set to Disabled. With more BIOS ROM space available, it will be able to support more advanced features as well as provide compatibility to a wide variety of peripheral devices. If a PS/2 keyboard is not available and you need to use a USB keyboard to install Windows (installation is performed in DOS mode) or run any program under DOS, set this field to Enabled.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.33NISE 100 User ManualChapter 4: BIOS SetupUSB 2.0 Controller This field is used to enable or disable the Enhanced Host Controller Interface (USB 2.0). Audio Controller This field is used to enable or disable the audio controller. Onboard LAN Controller This field is used to enable or disable the onboard LAN controller. PCIE Port Configuration This field is used to configure the PCIE port. On-Chip ATA Devices This field is used to configure the IDE drives.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.34NISE 100 User ManualChapter 4: BIOS SetupHardware Health Configuration This section is used to configure the hardware monitoring events such as temperature, fan speed and voltages.BIOS SETUP UTILITY Advanced Hardware Health Configuration CPU Warning Temperature CPU Shutdown Temperature CPU Temperature SYS Temperature +VCORE +1.05V +3.3V +5V +12V +1.8V [Disabled] [Disabled] : 46oC/114oF : 41oC/105oF : : : : : : 1.152 V 1.040 V 3.296 V 4.972 V 12.096 V 1.797 VCPU Shutdown Temperature You can prevent the system from overheating by selecting a temperature at which the system will shutdown. If the system detected that its temperature exceeded the one set in this field, it will automatically shutdown. This function will work only if your operating system supports the ACPI feature. CPU Temperature and SYS Temperature Detects and displays the current temperature of the CPU and the internal temperature of the system. +VCORE to +1.8V←→ ↑↓F1 F10 ESCSelect Screen Select Item General Help Save and Exit ExitDetects and displays the output voltage.v02.61 (C)Copyright , American Megatrends, Inc.CPU Warning Temperature This field is used to select the CPU’s temperature limit. Once the system has detected that the CPU’s temperature exceeded the limit, warning beeps will sound.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.35NISE 100 User ManualChapter 4: BIOS SetupBootMain Boot Settings Quick Boot Bootup Num-Lock Wait For ‘F1’ If Error Hit ‘DEL’ Message Display [Enabled] [On] [Enabled] [Enabled] Advanced Boot BIOS SETUP UTILITY Chipset Power Security ExitWait for ‘F1’ If Error When enabled, the system will wait for the &F1& key to be pressed when an error occurs. Hit ‘DEL’ Message Display When enabled, the system displays the “Press DEL to run Setup” message during POST.Configure settings during system boot.←→ ↑↓Enter Screen F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Go to Sub General Help Save and Exit ExitQuick Boot When Enabled, the BIOS will shorten or skip some check items during POST. This will decrease the time needed to boot the system. Bootup Num-Lock This allows you to determine the default state of the numeric keypad. By default, the system boots up with NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.36NISE 100 User ManualChapter 4: BIOS SetupChipsetThis section is used to configure the system based on the specific features of the chipset. Setting incorrect field values may cause the system to malfunction.BIOS SETUP UTILITY Chipset PowerInternal Graphics Mode Select Selects the amount of system memory used by the internal graphics device. Hyper Threading Technology This field is used to enable the functionality of the Intel? processor with Hyper-Threading Technology and will appear only when using this processor.MainAdvancedBootSecurity OptionsExitChipset Settings DRAM Frequency Boots Graphic Adapter Priority Internal Graphics Mode Select Hyper Threading Technologyu
Video[Auto] [PEG/PCI] [Enabled, 8MB] [Enabled]Auto 400 MHz 533 MHzFunction Configuration←→ ↑↓Enter Screen F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Go to Sub General Help Save and Exit ExitDRAM Frequency Selects the operating frequency of the DRAM. Boots Graphic Adapter Priority Selects which graphics controller to use as the primary boot device.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.37NISE 100 User ManualChapter 4: BIOS SetupVideo Function Configuration This section is used to configure the display device.BIOS SETUP UTILITY Chipset Video Function Configuration DVMT Mode Select DVMT/FIXED Memory Boot Display Device Flat Panel Type Local Flat Panel Scaling Panel Backlight Voltage [DVMT Mode] [128MB] [VGA+LVDS] [Bit 1C] [Auto] [2.5] Options Fixed Mode DVMT Mode Combo ModeDVMT/FIXED Memory Selects the graphics memory size used by the DVMT/Fixed mode. Boot Display Device Selects the type of display to use when the system boots. Flat Panel Type Selects the type of flat panel connected to the system. Local Flat Panel Scaling←→ ↑↓F1 F10 ESCSelect Screen Select Item General Help Save and Exit ExitSelects the local flat panel’s scaling method. Panel Backlight Voltage Selects the panel’s backlight voltage.v02.61 (C)Copyright , American Megatrends, Inc.DVMT Mode Select DVMT Mode Memory that is dynamically allocated based on memory requests made by an application and are released back to the system once the requesting application has been terminated. Fixed Mode Non-contiguous pagelocked memory allocated during driver initialization to provide a static amount of memory.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.38NISE 100 User ManualChapter 4: BIOS SetupPowerMain Advanced Boot BIOS SETUP UTILITY Chipset Power Security ExitSuspend Mode Selects the ACPI state to be used for system suspend.Enable / Disable ACPI support for Operating System. ENABLE: If OS supports ACPI. DISABLE: If OS does not support ACPI.Power Management Settings ACPI Function Suspend Mode Repost Video on S3 Resume Suspend Time Out Restore on AC Power Loss Resume By USB Device Resume On PME# Resume On RTC Alarm [Enabled] [S3 (STR)] [No] [Disabled] [Power Off] [Disabled] [Disabled] [Disabled]S1(POS) Enables the Power On Suspend function. S3(STR) Enables the Suspend to RAM function. Suspend Time Out←→ ↑↓Enter Screen F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Go to Sub General Help Save and Exit ExitSelects the time that the system enters the Suspend mode. Restore on AC Power Loss Power Off When power returns after an AC power failure, the system’s power is off. You must press the Power button to power-on the system. Power On When power returns after an AC power failure, the system will automatically power-on. Last State When power returns after an AC power failure, the system will return to the state where you left off before power failure occurs. If the system’s power is off when AC power failure occurs, it will remain off when power returns. If the system’s power is on when AC power failure occurs, the system will power-on when power returns.ACPI Function Enables or disables the Advanced Configuration and Power Interface (ACPI) of the Advanced Programmable Interrupt Controller (APIC). When enabled, the ACPI APIC table pointer is included in the RSDT pointer list.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.39NISE 100 User ManualChapter 4: BIOS SetupResume By USB Device Enables a USB device to wake up the system. Resume On PME# Enables the system to wake up to respond to PCI card such as LAN card or modem card that uses the PCI PME (Power Management Event) signal to remotely wake up the system. Access to the LAN card or PCI card will cause the system to wake up. Resume On RTC Alarm Enables the RTC to wake up the system.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.40NISE 100 User ManualChapter 4: BIOS SetupSecurityMain Advanced Boot BIOS SETUP UTILITY Chipset Power Security ExitTo clear the password, select Change Supervisor Password then press &Enter&. The Password Uninstalled dialog box will appear.Install or Change the password.Security Settings Supervisor Password User Password Change Supervisor Password Change User Password : Not Installed : Not InstalledIf you forgot the password, you can clear the password by erasing the CMOS RTC (Real Time Clock) RAM using the RTC Clear jumper. Refer to chapter 2 for more information. Change User Password This field is used to set or change the user password.←→ ↑↓Enter F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Change General Help Save and Exit ExitTo set a new password: 1. Select the Change User Password field then press &Enter&. 2. Type your password in the dialog box then press &Enter&. You are limited to eight letters/numbers. 3. Press &Enter& to confirm the new password. 4. When the Password Installed dialog box appears, select OK. To change the password, repeat the same steps above.Change Supervisor Password This field is used to set or change the supervisor password. To set a new password: 1. Select the Change Supervisor Password field then press &Enter&. 2. Type your password in the dialog box then press &Enter&. You are limited to eight letters/numbers. 3. Press &Enter& to confirm the new password. 4. When the Password Installed dialog box appears, select OK. To change the password, repeat the same steps above.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.41NISE 100 User ManualChapter 4: BIOS SetupExitMain Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Load Failsafe Defaults Advanced Boot BIOS SETUP UTILITY Chipset Power Security Exit system setup after saving the changes. F10 key can be used for this operation. ExitDiscard Changes To discard the changes, select this field then press &Enter&. A dialog box will appear. Confirm by selecting Yes to discard all changes made and restore the previously saved settings. Load Optimal Defaults Loads the optimal default values from the BIOS ROM. Load Failsafe Defaults←→ ↑↓Enter Screen F1 F10 ESC v02.61 (C)Copyright , American Megatrends, Inc.Select Screen Select Item Go to Sub General Help Save and Exit ExitLoads the fail-safe default values from the BIOS ROM.Save Changes and Exit To save the changes and exit the Setup utility, select this field then press &Enter&. A dialog box will appear. Confirm by selecting Yes. You can also press &F10& to save and exit Setup. Discard Changes and Exit To exit the Setup utility without saving the changes, select this field then press &Enter&. You may be prompted to confirm again before exiting. You can also press &ESC& to exit without saving the changes.Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.42NISE 100 User ManualAppendix A: Power ConsumptionAppendix A: power ConsumptionTest ConfigurationSystem Configuration Chassis CPU Memory HDD Keyboard Mouse CHASSIS NICE100 VER:A Intel? Atom? N270 1.6G/533M/512K/25W DDR2 667 SO-DIMM 128Mx8(16) 2GB 200PIN HDD 2.5 SATA HTSA360/7200RPM/250G/5V 800mA DC LEMEL B-5201-P GENIVS EASY MOUSE PS/2 VendorCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.43NISE 100 User ManualAppendix A: Power ConsumptionPower Consumption MeasurementPurpose The purpose of the power consumption test is to verify the power dissipation of the system and the load of the power supply. Test Equipment PROVA CM-07 AC/DC CLAMP METER Device Under Test DUT: Sys #1 Test Procedure 1. Power up the DUT then boot Windows XP. 2. Enter the standby mode (HDD power down). 3. Measure the power consumption and record it. 4. Run the Burn-in test program to apply 100% full loading. 5. Intel Kpower program. 5. LAN Packet Counter and Receive ProgramTest DataSys #1 +12V Full-Loading Mode Standby Mode 1.31A 15.72W 0.83A 9.96W Result Total 1.31A 15.72W 0.83A 9.96WCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.44NISE 100 User ManualAppendix B: GPI/O Programming GuideAppendix B: Gpi/O prOGrAmminG Guide#include &windows.h& #include &stdio.h& #include “winio.h” #pragma comment(lib,”WinIo.lib”) #pragma once bool bR // Call InitializeSMBUS to start the driver bResult = InitializeSMBUS(); if(bResult) { /*Initialized the DIO program*/ DWORD RetVal=0; /*Initialized the SMBUS controller*/ SMBUS_Write_Byte(0x30,0x01,0x07); SMBUS_Write_Byte(0x30,0x02,0); SMBUS_Write_Byte(0x30,0x03,0x78); SMBUS_Write_Byte(0x30,0x04,0); SMBUS_Write_Byte(0x30,0x09,0x08); SMBUS_Write_Byte(0x30,0x0A,0); SMBUS_Write_Byte(0x30,0x0B,0); SMBUS_Write_Byte(0x30,0x0C,0); SMBUS_Write_Byte(0x30,0x12,0xFF); SMBUS_Write_Byte(0x30,0x13,0x3F); SMBUS_Write_Byte(0x30,0x14,0x80); /*Reset all output pins to zero*/ RetVal=SMBUS_Read_Byte(0x01,0x30); RetVal=RetVal&0xF8; SMBUS_Write_Byte(0x30,0x01,RetVal); RetVal=SMBUS_Read_Byte(0x09,0x30); RetVal=RetVal&0xF7; SMBUS_Write_Byte(0x30,0x09,RetVal); /*Checking I/O pin 1*/ //Set I/O pin 1 to 0 RetVal=SMBUS_Read_Byte(0x09,0x30); RetVal=RetVal&0xF7; SMBUS_Write_Byte(0x30,0x09,RetVal); //Set I/O pin 1 to 1 RetVal=SMBUS_Read_Byte(0x09,0x30);Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.45NISE 100 User ManualAppendix B: GPI/O Programming GuideRetVal=RetVal|0x08; SMBUS_Write_Byte(0x30,0x09,RetVal); /*Checking I/O pin 3*/ //Set I/O pin 3 to 0 RetVal=SMBUS_Read_Byte(0x09,0x30); RetVal=RetVal&0xFE; SMBUS_Write_Byte(0x30,0x01,RetVal); //Set I/O pin 3 to 1 RetVal=SMBUS_Read_Byte(0x09,0x30); RetVal=RetVal|0x01; SMBUS_Write_Byte(0x30,0x01,RetVal); /*Checking I/O pin 5*/ //Set I/O pin 5 to 0 RetVal=SMBUS_Read_Byte(0x09,0x30); RetVal=RetVal&0xFD; SMBUS_Write_Byte(0x30,0x01,RetVal); //Set I/O pin 5 to 1 RetVal=SMBUS_Read_Byte(0x09,0x30); RetVal=RetVal|0x02; SMBUS_Write_Byte(0x30,0x01,RetVal); /*Checking I/O pin 7*/ //Set I/O pin 7 to 0 RetVal=SMBUS_Read_Byte(0x01,0x30);RetVal=RetVal&0xFB; SMBUS_Write_Byte(0x30,0x01,RetVal); //Set I/O pin 7 to 1 RetVal=SMBUS_Read_Byte(0x09,0x30); RetVal=RetVal|0x04; SMBUS_Write_Byte(0x30,0x01,RetVal); /*Reading current input*/ RetVal=SMBUS_Read_Byte(0,0x30); RetVal=((RetVal&0x78)&&3);//LSB 4 bits of retval--Pin 8,6,4,2//}Copyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.46NISE 100 User ManualAppendix C: Watchdog Timer SettingAppendix C: WAtChdog timer SettingTITLE EBC371FL Watchdog Sample code .model small .code main PROC ; Initial Watch Dog Timer Mov dx,2eh Mov al,87h Out dx,al Mov al,01h Out dx,al Mov al,55h Out dx,al Out dx,al Mov dx,2eh Mov al,07h Out dx,al Mov dx,2fh Mov al,07h Out dx,Setting up timer for 5 sec Mov dx,2eh Mov al,73h Out dx,al Mov dx,2fh Mov al,05h OutCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.47NISE 100 User ManualAppendix C: Watchdog Timer Settingdx,Start timer Mov dx,2eh Mov al,72h Out dx,al Mov dx,2fh Mov al,90h Out dx,al main ENDP END mainCopyright ? 2009 NEXCOM International Co., Ltd. All Rights Reserved.48NISE 100 User Manual
更多相关文档